background image

www.factorybuysdirect.com

200376-01A

12

INSTALLATION

FLOOR CLEARANCES

Hearth

5"

Min.

Combustible 

Material 

14"

Min.

Combustible 

Material 

Noncombustible Material 

Figure 8 - Minimum Fireplace Clearances 

If Installed at Floor Level

Figure 9 - Minimum Fireplace Clearances 

Above Combustible Flooring

A.  If installing appliance on the floor level, 

you must maintain the minimum distance 

of 14" to combustibles (see Figure 8).

B.  If combustible materials are less than 14" 

to the fireplace, you must install appliance 

at least 5" above the combustible flooring 

(see Figure 9).

Figure 10 - Attaching Heater Base to 

Fireplace Floor

INSTALLING HEATER BASE ASSEMBLY

Installation Items Needed

•  hardware package (provided with heater)
•  electric drill with 3/16" masonry drill bit
1.  Position  heater  base  assembly  in  fire-

place. Center base assembly left to right 

and front to back inside fireplace.

2.  Mark  screw  locations  through  holes  in 

mounting  brackets  (see  Figure  10).  If 

installing in a brick-bottom fireplace, mark 

screw locations in mortar joint of bricks.

3.  Remove heater base from fireplace.
4.  Drill holes at marked locations using 3/16" 

drill bit.

5.  Attach  base  assembly  to  fireplace  floor 

using  two  masonry  screws  provided  in 

hardware package (see Figure 10).

6.  Connect to gas supply. See 

Connecting 

To Gas Supply

, page 15.

 WARNING: You must secure 

this heater to fireplace floor. If 

not, heater will move when you 

adjust controls. Moving heater 

may cause a gas leak.

  WARNING:  If  installing  in  a 

sunken  fireplace,  special  care 

is  needed.  You  must  raise  the 

fireplace floor to allow access to 

heater control panel. This will in-

sure adequate air flow and guard 

against  sooting  and  controls 

being damaged. Raise fireplace 

floor with noncombustible mate-

rial. Make sure material is secure.

  CAUTION:  Do  not  pick  up 

heater base assembly by burners. 

This could damage heater. Only 

handle base assembly by grates.

IMPORTANT: 

Make sure the heater burners 

are level. If heater is not level, heater will not 

work properly.

Masonry 

Screw

Содержание FDLT24-1

































Отзывы: