Dulas VC150SDD Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 47

background image

VC150SDD Installation & Technician’s Manual

Page 40 of 47

Section 5 – Checking the Dulas Lightning Protection board

The Dulas Lightning Protection board

incorporates three Metal Oxide Varistors

(MOVs) lightning protection devices on the

board. These will absorb the small lightning

strikes that may occur nearby to the

installation but will not be effective against

large lightning strikes. If the MOVs are

damaged in the event of a large strike they

will fail and must the board must be

replaced.

To check if the board is still effective

conduct the following test:

1. Switch the PV isolator to “0”.

2. Wait two minutes or more to ensure the capacitor has discharged and then remove the

controller cover.

3. Disconnect the mating connectors from J1 and J2.

4. Ease the 4 plastic clips securing the circuit board to one side and remove the circuit board.

5. Visually check both sides of the board for signs of damage or discolouration.

6. Use a multi-meter set to the lowest resistance range to measure the resistance from

connection J1/ PV+ to J2/ +. This should be less than 0.15 ohms. It is sometimes
necessary to measure the resistance of the multimeter leads shorted together and subtract
this “zero” reading from the measured resistance of the circuit board.

7. Use a multi-meter set to the lowest resistance range to measure the resistance from

connection J1/ -PV to J2/ -. This should be less than 0.1 ohms. It is sometimes necessary
to measure the resistance of the multimeter leads shorted together and subtract this “zero”
reading from the measured resistance of the circuit board.

8. Use a mulitmeter set to its highest resistance range to measure the resistance between J2

/+ and J2/ -. This should be greater than 1M ohm. Be careful to ensure that you are not
touching the connections as the reading is being taken as this will lower the measured
resistance.

If all the above tests are satisfactory the board can be re-installed. If any tests fail a
replacement board should be installed.

«
...
38
39
40
41
42
...
»

Содержание VC150SDD
















































Отзывы:

Нет отзывов

Похожие инструкции для VC150SDD

Бренд: U-Line Страницы: 12

Бренд: U-Line Страницы: 24

Бренд: Zanotti Страницы: 44

ChefLine CHPZ2P

Бренд: CHEFOOK Страницы: 102

Бренд: Igloo Страницы: 11

Бренд: Fhiaba Страницы: 27

GLR12B D16 Series

Бренд: Galanz Страницы: 26

Wine Captain U-2224ZWCINT-60B

Бренд: U-Line Страницы: 14

Бренд: Zanussi Electrolux Страницы: 16

Бренд: Dometic Страницы: 12

Бренд: U-Line Страницы: 39

Бренд: Premium Страницы: 23

Бренд: VALPRO Страницы: 31

Бренд: Westinghouse Страницы: 40

Бренд: Phocos Страницы: 48

Бренд: Signature Страницы: 35

Бренд: barkman Страницы: 6

ERB 21880 NXA++

Бренд: ECG Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды