Duemmegi Domino DFDALI Скачать руководство пользователя страница 8

Страница: 8 / 11

Domino

DFDALI

Global Settings

In this TAB, Figure 5, it is possible to set, for all ballasts on
the DALI line, the following parameters:

MIN

: minimum brightness value (%); enabling the Reset

check box, the default value will be restored (1%).

MAX

: maximum brightness value (%); enabling the Reset

check box, the default value will be restored (100%).

BUS F.

: the brightness value (%) to be recalled by ballasts

during failure of

Domino

and/or DALI bus.

Ramp

: the ramp value in seconds.

Preset

: writing a value (0 to 100) and clicking on the button

on the right side, the brightness will be forced to that value.

M16

: the value to be loaded into the 16 presets; the

button on the right side allows to recall the related preset
stored into the ballast.

DUEMMEGI

s.r.l. - Via Longhena, 4 - 20139 MILANO

Tel. 02/57300377 - Fax 02/55213686 –

www.duemmegi.it

Rel.: 2.1 May 2013

Page 8 of 11

HOME AND BUILDING AUTOMATION

Figure 5: Global Setting

Figure 6: Status

Содержание Domino DFDALI












Результаты поиска

Содержание Domino DFDALI

Отзывы:

Похожие инструкции для Domino DFDALI

Бренды по названию

Популярные бренды

Duemmegi Domino DFDALI, Руководство пользователя

Результаты поиска

Содержание Domino DFDALI

Отзывы:

Похожие инструкции для Domino DFDALI

Бренды по названию

Популярные бренды