DTS X BRICK Скачать руководство пользователя страница 9

 

 

User Manual 

Ver. 1.04 

7 di 35 

 

 

 X 

BRICK 

 

 

 

 

3.4 Safety 

 

 

Risk Group 2 product according to IEC 62471.  

Do not look directly at the light output and do not stare at the light beam 

through optical instruments or any other device that may concentrate the light 

beam. May be harmful to the eyes and skin. 

 

 

 

 

 

Do not stare at the operating light source. 

The luminaire should be positioned so that prolonged staring into the 

luminaire from a minimum distance of 25,94 m is not expected. 

 

 

The light source contained in this luminaire shall only be replaced by the 

manufacturer or their service agent or a similar qualified person. 

 

The unit is not for domestic use and must be installed by a qualified electrician or 

experienced person only. 

 

The projector should always be installed with the proper tools. The fixing point must 

always be capable of supporting the weight of the unit. 

 

Always use a safety cable to sustain the weight of the unit in case of failure of the 

main fixing point.  

 

 

The external surface of the unit’s body, at various points, may exceed 50 °C. 

Never handle the unit until at least five minutes have passed since it was 

turned off. 

 

 

 

 

 

Ambient temperature should not exceed 40 °C. 

 

This fixture is intended for use where humidity does not exceed 90% (non-

condensing). 

 

After storage, and before switching on the fixture, please ensure that its ambient 

temperature has been restored to acceptable values. 

 

Never install the fixture in places that lack a constant air flow.

 

3.5 

Waste Electrical and Electronic Equipment (WEEE) Directive: 

 

 

 

 

The projector, the accessories, and the packaging should be sorted for 

environmental-friendly recycling. 

For EC countries: according to the European Directive 2012/19/EU for Waste 

Electrical and Electronic Equipment and its implementation into national right, 

luminaires that are no longer usable must be collected separately and disposed of in 

an environmentally correct manner. 

Содержание X BRICK








































Отзывы: