manualshive.com logo in svg

Dspecialists ISOSTEM Expert, Руководство пользователя

Поделиться
Скачать
Dspecialists ISOSTEM Expert Скачать руководство пользователя страница 33

ISOSTEM     USER MANUAL

GUI Software Reference     33

M

ULTIFUNCTIONAL

A

REA

The multifunctional area in the top right-hand section of the Expert tab fea-
tures nine view modes that are selected using sub-tabs. Among others,
they can be used to visualize parameter edits in audio processing modules

such as the Panoramic Analyzer
or the Virtual Microphone.

Direct Window

The direct module connects any multichannel sources present at the audio
inputs directly to the internal bus. This module is particularly important for

processing native multichannel programs.

L-R

This fader adjusts the direct level of the L and R front chan-
nels.

Unit: dB
Range: 0 dB - -inf

L-R Mute/Solo

These buttons are used to mute or solo the L-R fader signal.

C

This fader adjusts the direct level of the Center channel.

Unit: dB
Range: 0 dB - -inf

LFE

This fader adjusts the direct level of the LFE channel.

Unit: dB
Range: 0 dB - -inf

C/LFE Mute/Solo

These buttons are used to mute or solo the Center and LFE fader signals.

SL-SR

This fader adjusts the direct level of the SL and SR rear channels.

Unit: dB
Range: 0 dB - -inf

SL-SR

 Mute/Solo

These buttons are used to mute or solo the SL-SR fader signal.

Содержание ISOSTEM Expert






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды