manualshive.com logo in svg

DSE DSEPOWER DSE871 Series, Руководство пользователя

Поделиться
Скачать
DSE DSEPOWER DSE871 Series Скачать руководство пользователя страница 55

Protections 

 

Part No. 057-129   DSE871x mono remote display ISSUE 2.1  21/09/2010 ADM    

55

 

 

6.9  ROCOF / VECTOR SHIFT 

 
When configured to run in parallel with the mains (utility) supply, the module monitors for ROCOF / Vector shift trips 
according to the module’s configuration settings. This is included within the module and will detect failure of the 
mains supply during parallel operation with the generator. 
 

NOTE:

NOTE:

NOTE:

NOTE:----    This protection operates only when in parallel with the mains supply and is disabled at all 

This protection operates only when in parallel with the mains supply and is disabled at all 

This protection operates only when in parallel with the mains supply and is disabled at all 

This protection operates only when in parallel with the mains supply and is disabled at all 

other times.

other times.

other times.

other times.    

 
Should either of these alarms operate, the module will perform a controlled shutdown (electrical trip) of the 
generator. This operation must be manually reset : 
 

1)  Press 

 button. The engine will stop if it is still running and the alarm is cleared. 

2)  Activate digital input configured to “Clear ROCOF/Vector shift” if this has been provided. 

3)  Press 

 and 

 button together and hold for 5 seconds. The ROCOF/Vector shift instrument is displayed 

and all ‘peak hold’ values are reset, clearing the ROCOF/Vector shift alarm. 

 
For details on activating and configuring the ROCOF/Vector shift protection, you are referred to the 8700 
configuration software manual. 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Содержание DSEPOWER DSE871 Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды