DSE DSEPOWER DSE871 Series Скачать руководство пользователя страница 20

Страница: 20 / 68

Installation – Description Of Controls

Part No. 057-129 DSE871x mono remote display ISSUE 2.1 21/09/2010 ADM

4.2 DESCRIPTION OF CONTROLS

The following section details the function and meaning of the various controls on the module.

4.3 DSE8711 DISPLAY FOR DSE8710 AUTOSTART

NOTE:- “Generator on load” LED has two modes of operation depending upon the configuration of the

controllers digital inputs.
1) Digital input configured for “Generator closed auxiliary” – The LED illuminates when the generator

closed auxiliary input is active – The LED shows the state of the auxiliary contact.

2) There is NO input configured for “Generator closed auxiliary” (factory default setting) – The LED

illuminates when the DSE8710 gives the loading signal to the generator – The LED shows the state of
the DSE8710s loading request.

Menu navigation
buttons

Four configurable
LEDs

Select Stop
mode

Select Manual
mode

Select
Auto
mode

Mute
alarm /
Lamp
test

Start
engine
(when in
manual
mode)

Close
generator
(manual mode
only)

Open
generator
(manual mode
only)

Main status and
instrumentation display

Close Generator LED.
On When The Generator
Is Required To Be On
Load.

Generator Available
LED.
On when the
generator is within
limits and able to
take load.

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Содержание DSEPOWER DSE871 Series





































































Результаты поиска

Содержание DSEPOWER DSE871 Series

Отзывы:

Бренды по названию

Популярные бренды

DSE DSEPOWER DSE871 Series, Руководство пользователя

Результаты поиска

Содержание DSEPOWER DSE871 Series

Отзывы:

Бренды по названию

Популярные бренды