DSE DSE8661 Скачать руководство пользователя страница 61

Страница: 61 / 120

Installation

4.3 TYPICAL ARRANGEMENT OF DSENET®

CAUTION!: The DSE8661 modules MUST NOT be connected together using only the

DSENet® Port on each module as it is not isolated.

NOTE: For further details on connection between the DSE8661 modules using DSENet®,

see the section entitled

DSE8661 (DSENet

to RS485) Typical Wiring Diagram

elsewhere in

this document.

NOTE: For further details of module configuration, refer to DSE Publication:

057-215

DSE8661 Configuration Suite Software Manual.

NOTE: A maximum of 20 DSENet® expansion modules can be connected to the DSE host

module, made up of the following devices :

Module

Maximum Number Supported

DSE2130 Input Expansion

DSE2131 Ratiometric Input Expansion

DSE2133 RTD/Thermocouple Intput Expansion

DSE2152 Analogue Output Expansion

DSE2157 Relay Output Expansion

DSE2548 LED Expansion

Содержание DSE8661

























































































































Результаты поиска

Содержание DSE8661

Отзывы:

DSE DSE8661, Руководство оператора, Страница: 61 / 120

Результаты поиска

Содержание DSE8661

Отзывы: