DSE DSE8661 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 120

DSE DSE8661 Скачать руководство пользователя страница 45

Installation

45

4.1.6 MAINS CURRENT TRANSFORMERS

WARNING!: Do not disconnect this plug when the CTs are carrying current.

Disconnection open circuits the secondary of the C.T.’s and dangerous voltages may then
develop. Always ensure the CTs are not carrying current and the CTs are short circuit
connected before making or breaking connections to the module.

NOTE: The module has a burden of 0.5 V A on the CT. Ensure the CT is rated for the

burden of the controller, the cable length being used and any other equipment sharing the
CT. If in doubt, consult the CT supplier.

NOTE: Take care to ensure correct polarity of the CT primary as shown below. If in doubt,

check with the CT supplier.

NOTE: DO NOT CONNECT terminals 54, 56 and 57 as they are not applicable.

Pin

No

Description

Cable

Size

Notes

51

CT Secondary for L1

2.5mm²

AWG 13

Connect to s1 secondary of L1 monitoring CT

52

CT Secondary for L2

2.5mm²

AWG 13

Connect to s1 secondary of L2 monitoring CT

53

CT Secondary for L3

2.5mm²

AWG 13

Connect to s1 secondary of L3 monitoring CT

54

-

DO NOT CONNECT: Not applicable

55

CT Common

2.5mm²

AWG 13

Connect to s2 secondary of L1, L2 & L3 CTs and to a good clean earth
point.

56

CT Secondary for
Bus/Load CT

-

DO NOT CONNECT: Not applicable

57

CT Secondary for
Bus/Load CT

-

DO NOT CONNECT: Not applicable

4.1.6.1 CT CONNECTIONS

p1,

k

or K is the primary of the CT that ‘points’ towards the Mains

p2,

l

or L is the primary of the CT that ‘points’ towards the Load

s1 is the secondary of the CT that connects to the DSE Module’s input for the CT measuring

s2 is the secondary of the CT that should be commoned with the s2 connections of all the other CTs
and connected to the CT common terminal of the module.

TO MAINS

TO LOAD

POLARITY OF CT PRIMARY

Labelled as

p1,

k

or K

Labelled as

p2,

l

or L

«
...
43
44
45
46
47
...
»

Содержание DSE8661

























































































































Отзывы:

Нет отзывов