manualshive.com logo in svg

DSC WLS920, Руководство по установке, Страница: 16 / 32

Поделиться
Скачать
DSC WLS920 Скачать руководство пользователя страница 16

12

System Programming

s

e

c

t

i

o

n

6

6.1

Programming Access Codes

There are 9 access codes programmable by the end user. All codes have the ability to arm and disarm the
system. Instructions for programming access codes are located in the WLS920 Instruction Manual.
The user-programmed codes are as follows:

Master Code – Access Code (40)

By default, the Master Code is enabled to perform any keypad function. This code can be used to program all
User Codes. This code can also be programmed by the installer in programming section [007].The Master
Code can only be changed by the Installer.

General Access Codes – Access Codes (01) to (08)

General access codes can arm and disarm the system. By selecting the 

No Code Required for Bypassing

option, each user can also have the ability to bypass zones without entering an access code. To limit the
bypassing ability for a user, disable the bypassing attribute for that user code (see “Programming Access
Codes” in the WLS920 Instruction Manual).
The Master code and the Installer’s code are programmed in Installer’s programming.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

No Code Required For Bypassing ............................... Section [015], Option [5]
Installer’s Code ............................................................................... Section [006]

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Master Code ................................................................................... Section [007]

6.2

Telephone Line Monitor (TLM)

The panel will supervise the presence of the phone line and will indicate a trouble condition if the phone line is
disconnected. If the 

TLM Enabled 

option is selected, the panel will wait for the 

TLM Trouble Delay 

time

period before indicating the trouble so that a momentary interruption of the phone line will not cause a trouble
condition.
If the 

TLM Trouble Only When Armed 

option is enabled, the panel will indicate a TLM trouble only at the

control unit if the system is armed. To activate the bell output in the case of a TLM trouble while the system is
armed, the 

TLM Audible When Armed 

option must be selected.

When the trouble condition is restored, the panel can send a 

TLM Restoral 

Reporting Code. Any events which

occur while the phone line is down will also be communicated.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

TLM Enable/Disable ..................................................... Section [015], Option [7]
TLM Trouble Only When Armed or
TLM Audible When Armed ........................................... Section [015], Option [8]
TLM Trouble Reporting Code ......................................................... Section [349]
TLM Restoral Reporting Code ....................................................... Section [350]

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

TLM Trouble Delay .......................................................................... Section [370]

6.3

Bell Cut-off

The siren will silence after the number of seconds programmed for the 

Bell Cut-off 

time have passed.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Bell Cut-off ...................................................................................... Section [005]

6.4

Test Transmission

To ensure that the communication link with the central station is functioning properly, the panel can be
programmed to send a test transmission signal on a regular basis.
The panel can send a 

Periodic Test Transmission Reporting Code 

at the programmed 

Test Transmission

Time of Day

. The 

Test Transmission Cycle 

determines the number of days (001 to 255) between tests. If the

test transmission cycle being programmed is of a lesser value than the previous value, the system will wait the
original period before the next test transmission is sent, and then begin reporting with the new interval.
The end user can generate a communicator test. If the 

System Test Reporting Code 

is programmed, the

panel will send the signal when the System Test command is entered (see the WLS920 Instruction Manual for
information on performing a System Test).

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Test Transmission Reporting Codes .............................................. Section [352]
Test Transmission Time of Day ....................................................... Section [371]

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Test Transmission Cycle ................................................................. Section [370]

Содержание WLS920

































Отзывы:

Нет отзывов