DSC PC51O2-433NA Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

DSC PC51O2-433NA Скачать руководство пользователя страница 7

3

S E C T I O N 2

This section describes how to set up and wire the PC5102-433 module.

2.1 Choose a Mounting Location for the PC5102-433

NOTE

NOTE

NOTE

NOTE

NOTE: Mount the PC5102-433 receiver and wireless keys after you have done
placement tests with the wireless keys (see sections 5.1 and 5.2).

Find a place that is:

• Dry
• Close to the point of entry
• As high as possible
• Far from sources of interference, including: electrical noise (computers,

televisions and electric motors in appliances and heating and air
conditioning units); large metal objects like heating ducts and plumbing
which may shield the antenna.

Make sure that electrical wires will not run over the antenna of the module when it is
mounted.
When mounting the PC5102-433 in a basement, place the module as high and as
close to the underside of the first floor as possible. The range of the module will be
reduced if the unit is mounted below ground level.

2.2 Terminal Descriptions

The PC5102 has 2 on-board relay outputs which can be used in many different
applications. They can be used to activate LEDs, open garage doors, trigger X-10
devices etc.

NO1

NC1 COM1 NO2

NC2 COM2 RED

BLK

YEL

GRN

NO1

PGM1 Normally Open Relay Contact

NC1

PGM1 Normally Closed Relay Contact

COM1

PGM1 Relay Common Contact

NO2

PGM2 Normally Open Relay Contact

NC2

PGM2 Normally Closed Relay Contact

COM2

PGM2 Relay Common Contact

RED

Keybus Power +12V

BLK

Keybus Ground

YEL

Keybus Clock

GRN

Keybus Data

PC5102-433 Set Up & Wiring

«
...
5
6
7
8
9
...
»

Содержание PC51O2-433NA

























Отзывы:

Нет отзывов