background image

4

HSPA(3G)/Dual Alarm Communicator Installation Manual

Ratings Compatibility              

NOTE: 

Enter [*][8][Installer Code][900] at keypad to view the panel version number.

Products or components of products, which perform communications functions only shall comply

with the requirements applicable to communications equipment as specified in UL60950 or CAN

CSA C22.2. No. 60950-1, Information Technology Equipment - Safety - Part 1: General Require-

ments. Where network interfaces are external to the control unit or receiver, compliance to CAN

CSA C22.2. No. 60950-1 is adequate. Such components include, but are not limited to: hubs; rout-

ers; NIDs; third-party communications service providers; DSL modems; and cable modems.

This HSPA(3G)/dual-path alarm communicator shall be installed by service persons only (service

person is defined as a person having the appropriate technical training and experience necessary to

be aware of hazards to which that person may be exposed to in performing a task and can also take

measures to minimize the risks to that person or other persons). The Communicator shall be

installed and used within an environment that provides the pollution degree max 2, overvoltages

category II, in non-hazardous, indoor locations only. This manual shall be used with the installa-

tion manual of the panel which is connected to the communicator. All instructions specified within

the panel manual must be observed.
All the local rules imposed by local electrical codes shall be observed and respected during instal-

lation.

Installing the Ethernet Cable(TL2803G(R) Only)

A Category 5 (CAT 5) Ethernet cable must be run from a source with Internet connectivity to the

communicator module, inside the panel. The communicator end of the cable must be terminated

with an RJ45 plug, which will connect to the communicator’s RJ45 jack after the communicator is

installed. All requirements for installation of CAT5 Ethernet cable must be observed for correct

operation of the communicator, including, but not limited to, the following:

Table 1: Communicator Ratings

Model

3G2080(R) 

Cellular only

TL2803G(R)

Internet and Cellular 

Power Supply Ratings

Input Voltage

10.8-12.5 VDC

Power is supplied from the panel’s PC-Link header or a PCL-422 module in 

remote cabinet installations. In remote cabinet installations, the PCL-422 module 

located with the communicator is powered by either an HSM2204 or an 

HSM2300. Refer to the PCL-422 installation instructions for details. 

Current Consumption

Standby Current

90mA @ 13.66V

120mA @ 13.66V

Alarm (Transmitting) Current

400mA @ 12V

Operating Frequency

850MHz, 1900MHz

Typical Antenna Gain

2dB

i

Environmental Specifications

Operating Temperature

 14°F to 131°F (-10°C to 55°C) 

Humidity

5% ~ 93% relative humidity, non-condensing

Mechanical Specifications

Board Dimensions (mm)

100 × 150 × 15 

100 × 150 × 15 

Weight (grams) with bracket

310 

320 

Table 2: Compatible Receivers, and Panels  

Communicator

Receiver/

Panel 

Description

3G2080(R)

TL2803G(R)

Receiver

• Sur-Gard System I-IP Receiver, version 1.13+

• Sur-Gard System II Receiver, version 2.10+

• Sur-Gard SG-DRL3-IP, version 2.30+ (for Sur-Gard System III Receiver)

• Sur-Gard SG-DRL4-IP version 1.20+ (for Sur-Gard System IV Receiver)

• Sur-Gard SG-DRL5-IP version 1.00+ (for Sur-Gard System 5 Receiver)

Panel

• HS2016

• HS2032

• HS2064

• HS2128

C

OMMUNICATOR

 I

NSTALLATION

 C

ONFIGURATION

Содержание 3G2080





















Отзывы: