background image

 

 

Page 6  

4.4   ASSEMBLY/DISASSEMBLY 

 

No pump assembly operations are envisaged. 

For wall mounting ensure adequate space is available (as shown in the installation diagram) to avoid abnormal postures and 

possible impacts; four fixing holes are provided with different characteristics depending on the version (see section 2.2) 

Subsequently it will be necessary, as previously described, to connect the pump to the machine hydraulically and then to 

connect the control panel. 

During the disassembly phase ensure the tank is empty. 

Disconnect the electrical and hydraulic parts. 

Where the machine is to be scrapped, do not dispose of potentially polluting parts in the environment, following local 

regulations for their correct disposal. 

At the time of the machine being scrapped it is necessary to remove and destroy the identification plate and all other relative 

documents. 

 

4.5  REGULATION 

 

The only parameter which can be modified is the pressure; to modify the value increase or decrease the pressure of the 

command air supply. 

 

4.6

 

MAINTENANCE 

 

 

 

 

Having undergone rigorous testing by ourselves, the pump does not require any further maintenance. The use of lubricants free 

from impurities is recommended and the periodic careful cleaning of the component parts of the pump. 

Disassembly must be effected in the following manner: 

 

1.

 

Disconnect the tubing attached to the pump. 

2.

 

Remove the fixing screws and the tank and relative cover. 

3.

 

Remove the suction filter and the relative valve. 

4.

 

Unscrew the cylinder paying 

particular attention

 to the loading of the springs; the component parts of the pump unit can 

then be disassembled. 

5.

 

Remove the screws which retain the flange so releasing the complete pump unit. 

 

In this way all component parts of the pump unit can be removed allowing the disassembly and cleaning of the  release and 

suction valves. 

All pieces should be washed in petrol and lubricated prior to reassembly. 

 

The following should be checked periodically: 

 

 

VERIFY 

WORK CYCLES 

The state of lubrication 

100 

The oil level 

200 

The cleanliness of the suction filter 

400 

That the tank is clean and the bottom free from deposits 

600 

 

 

The machine does not require any special tools to carry out checks or maintenance tasks, However, it is recommended that only 

tools suitable for the tasks and in good condition should be utilised (according to current regulation) to avoid injury to persons 

or damage to machine parts 

 

 

 

 

 

 

WARNING

Locate the machine in conditions which facilitate easy access. 

Utilise individual protection to avoid contact with mineral oil or grease. 

 

 

Содержание 31030 Series












Отзывы: