background image

Heatmax Furnace Installation and Operation Manual 

 

35 

In  such  a  case,  when  starting  up  the  fire,  do  not  operate  appliances  that  evacuate  air 
outside the house, such as: 

  Range hood 

  Air exchanger 

  Clothes dryer 

  Bathroom blower 

  Ventilated central vacuum system 

Exhaust  blowers  that  are  in  a  fuel  storage  room  should  be  installed  so  as  not  to  create 
negative pressure in the room where the solid fuel appliance is located. 

A fresh air supply may be necessary to prevent solid fuel units from rejecting products of 
combustion  into  the  house.  The  indications  used  to  determine  if  an  additional  fresh  air 
supply  is  necessary  are  not  appropriate  for  all  the  situations.  When  in  doubt,  it  is 
recommended to install a fresh air supply.  

A fresh air supply may be needed if:  

-

  Solid  fuel  units  present  anomalies,  such  as  irregular  draft,  smoke  return,  bad 

combustion, and/or reversed draft (whether there is combustion or not);  

-

  Existing solid fuel units such as a stove or fireplace release odours, heat badly, cause 

smoke returns, or reversed draft (whether there is combustion or not ); 

-

  The  opening  of  a  window,  even  slightly,  in  calm  weather  (windless),  eliminates  every 

problem mentioned above ; 

-

  The  house  is  equipped  with  a  tight  vapour  barrier  and  adjusted  windows,  and/or  is 

equipped with an interior air mechanical evacuation device ; 

-

  There is excessive condensation on the windows in winter; and 

-

  The house is equipped with a ventilation system.  

If, according to these symptoms or other similar ones, there is insufficient combustion air, it 
is necessary to ensure an additional combustion air supply.  

Additional  combustion  air  can  be  provided  following  the  following  methods,  provided  that 
they satisfy chapter 4 of the CSA B365 standard for Canada:  

-

  Direct  connection:  solid  fuel  units  can  be  connected  directly  to  a  source  of  new 

combustion air only if they are certified for this kind of installation, which must respect 
the manufacturer’s instructions.  

-

  Indirect  method:  new  combustion  air  can  be  brought  into  a  pipe  located  within 

approximately 300mm (12 inches) of the unit.  If the pipe is too close to the furnace, it 
may interfere with its operation. 

-

  Mechanical  ventilation  system:  if  the  house  is  equipped  with  a  ventilation  system  (air 

exchanger or heat recovery), the ventilation system may provide sufficient auxiliary air 
to  the  solid  fuel  unit.  Otherwise,  the  owner  should  be  informed  that  the  ventilation 
system  may  have  to  be  rebalanced  by  a  ventilation  technician  after  the  installation  of 
the solid fuel unit. 

Содержание DF01000






































































Отзывы: