DriSteem CRUV 10 Скачать руководство пользователя страница 43

Страница: 43 / 56

CRUV INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

MAINTENANCE

RO/DI water option

5. Check the operation of the float valve and the condition of the float seat.

6. Check the low water switch to make sure the float slides freely on the stem.

7. Secure the chamber cover making sure the cover gasket is seated and the

chamber is sealed.

8. Reinstall the evaporating chamber.

• Reconnect the ﬁ ll line.

• Reconnect electrical plugs (the plugs are color coded).

• Reconnect drain union.

• Reconnect steam hose.

9. Verify electrical connections:

• Verify that all DIN rail-mounted components are securely fastened to DIN

rail.

• Verify that all power terminal screws and lugs are tight from power block

to heaters.

• Verify that all plugs are completely plugged in.

10. Close the drain valve.

11. Turn on the water supply.

12. Turn on the electrical power.

OFF-SEASON SHUT-DOWN PROCEDURE

1. Switch off electric power.

2. Remove the enclosure.

3. Shut off the water supply to the makeup valve.

4. Drain the evaporating chamber by opening the drain valve. For units with

an end-of-season drain, refer to the

Vapor-logic Installation and Operation

Manual

5. Replace the enclosure.

6. Leave the evaporating chamber dry, the power off, and the water shut-off

valve closed until the next humidification season.

mc_061610_1520

Содержание CRUV 10

























































Результаты поиска

Содержание CRUV 10

Отзывы:

Похожие инструкции для CRUV 10

Бренды по названию

Популярные бренды

DriSteem CRUV 10, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CRUV 10

Отзывы:

Похожие инструкции для CRUV 10

Бренды по названию

Популярные бренды