Drill Master 61626 Скачать руководство пользователя

Страница: 6 / 16

Page 6

For technical questions, please call 1-800-444-3353.

Item 61626

SAFET

Op
ERA
TION

AINTENAN

SETU
p

Grounding

TO pREVENT ELEcTRIc SHOcK AND DEATH FROM

INcORREcT GROUNDING WIRE cONNEcTION:

check with a qualified electrician if you are in doubt as to whether the outlet is properly

grounded. Do not modify the power cord plug provided with the tool. Never remove the

grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have

it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by

a qualified electrician.

Grounded Tools: Tools with Three prong plugs

3-prong plug and Outlet

1. Tools marked with “Grounding Required” have

a three wire cord and three prong grounding

plug. The plug must be connected to a properly

grounded outlet. If the tool should electrically

malfunction or break down, grounding provides

a low resistance path to carry electricity away

from the user, reducing the risk of electric shock.

(See 3-prong plug and Outlet.)

2. The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire

in the cord must be the only wire connected to

the tool’s grounding system and must never

be attached to an electrically “live” terminal.

(See 3-prong plug and Outlet.)

3. The tool must be plugged into an appropriate outlet,

properly installed and grounded in accordance

with all codes and ordinances. The plug and outlet

should look like those in the preceding illustration.

(See 3-prong plug and Outlet.)

Double Insulated Tools: Tools with Two prong plugs

Outlets for 2-prong plug

1. Tools marked “Double Insulated” do not

require grounding. They have a special

double insulation system which satisfies

OSHA requirements and complies with

the applicable standards of Underwriters

Laboratories, Inc., the Canadian Standard

Association, and the National Electrical Code.

2. Double insulated tools may be used in either of the

120 volt outlets shown in the preceding illustration.

(See Outlets for 2-prong plug.)

Содержание 61626

















Результаты поиска

Содержание 61626

Отзывы:

Похожие инструкции для 61626

Бренды по названию

Популярные бренды

Drill Master 61626, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 61626

Отзывы:

Похожие инструкции для 61626

Бренды по названию

Популярные бренды