Before each use
Inspect the electrical cord for
damage.
Look for fraying, cuts, etc.
Do not use the unit if you find any
damage. Call Dri-Eaz for the nearest
Service Center at 800-932-3030.
Inspect and vacuum filter as
needed.
Keep a clean filter in the unit
at all times to protect internal
components from dust and other
particulate build-up. The 1200 is
equipped with a 3M™ High Air-Flow
filter. The HAF filter may be vacuumed
clean and reused up to three times.
Do not rinse or wash the HAF filter
,
as it will reduce the effectiveness of
the electrostatic material.
Replace only with a new 3M HAF
Filter (Dri-Eaz part no. F368). For
parts and service call your local
distributor or contact the Dri-Eaz Service Department at
800-932-3030.
CAUTION:
Dust can cause the unit to overheat and
shut down. Do not operate when excessive dust or
airborne particles are present, such as during
sanding or spray-painting. Inspect and clean air filter
elements and coils frequently.
IMPORTANT: Replace the HAF filter whenever 1)
it has been vacuumed clean 3 times or 2) it has
been used on a mold remediation job or
otherwise exposed to potentially dangerous
contaminants.
Monthly
Check coils
. Dirty coils can cause the unit to overheat.
Clean when visibly dirty. See Fig. B.
1. Unplug unit.
2. Remove housing, locate coils and allow coils to dry if
wet.
3. Vacuum both sides of the
coils until clean, being careful
not to let the nozzle touch the
fins; as that may cause
damage by bending them.
Check catch basin tray.
Clean when dirt and debris
are present.
1. Wipe clean with a rag.
Check drain hose.
1. Look for obstructions.
Disconnect and clear any
debris present.
2. Reattach gravity drain
hose.
Annually
Have the pump system
inspected by the Dri-Eaz Service Department
(800-932-3030) or by a qualified service center.
TRANSPORT AND STORAGE
NOTICE:
Handle the unit carefully. Do not drop, throw,
or place the unit where it could fall. Rough treatment can
damage this equipment and may create a hazardous
condition or void warranty.
IMPORTANT:
Be sure to purge the water from the pump
reservoir before moving the unit. See the PURGE
function under "How to use the control panel" on page 2.
Note that the unit must be plugged in for the Purge
function to operate.
1. Do not expose the control panel to moisture, snow or
rain when transporting in uncovered vehicles.
2. Store and transport securely to avoid any damaging
impact to internal parts.
READ AND SAVE
THESE INSTR
ERROR MESSAGES
The table below shows error message that the system may detect. If the display shows an “ER” message, first unplug the
unit and then plug it back in. This may re-set the electronics, and if so, no further action is required. If the error message
reappears, try the solution shown under “Explanation.” If this still does not fix the problem, contact your local authorized
service center or the Dri-Eaz Service Department at 800-932-3030.
E R R O R
M E S S A G E
E X P L A N A T I O N
ER 1, 2, 3, 5, 6
Problem with electronic control panel. Contact Dri-Eaz Service.
ER 4
Check the temperature or sensor cable. Contact Dri-Eaz Service for instructions.
ER 8
Check the control panel keys. Press and release each key several times.
ER 9
Check for obstructions or kinks in the drain hose.
Catch basin
tray
Coils
Pump
FIG. B: CLEANING
07-01502B 2014-04 Warranty 07-00427
4
Dri-Eaz Products, Inc.
