Dream Vision DreamScaler4, Руководство пользователя

Страница: 10 / 40

3.0 SETUP
10 R699761 - DreamScaler 4 User Manual
3.0 SETUP
3.1 Initial Set-Up
STEP 1 - Power Up
1) Attach the removable power cord to the external power supply.
2) Plug the removable power cord into a wall outlet or power conditioner, if applicable.
3) Plug the small connector attached to the cable that comes out of the power supply into the DreamScaler 4.
The DreamScaler 4 should power on and display ‘DreamVision Powered by ABT’ on the FPD.
STEP 2 - Connect the scaler to your display
Once you have installed the DreamScaler 4 into your system, you must properly configure it for the display device
being driven. The DreamScaler 4 is shipped from the factory with the following preset default settings:
• Input Select is set to AUTO, to automatically detect an active input in a pre-configured priority.
• The Digital Video output is selected with RGB 4:4:4 color space
• The output format is set to SMPTE 274M, 1080p@50Hz or 1080p@60Hz according to the active source refresh
rate.
Use either the remote control or the front panel controls to perform the initial setup of the DreamScaler 4's output.
The procedure below uses the front panel buttons to perform initial setup.
Accessing the DreamScaler 4’s On Screen Display is crucial, not only in allowing you to navigate the menu of the
DreamScaler 4, but also to let you know that the DreamScaler 4 is sending a compatible signal to the display. If the
OSD is not visible on the display’s screen when you press one of the sub-menu buttons on the remote control, then
you must configure the DreamScaler 4 Signal output to obtain a compatible signal.
Displays with a DVI or HDMI Input
The default output on the DreamScaler 4 is digital RGB 4:4:4 (DVI Standard). The default format output is
1920x1080 progressive (1080p). If you don’t have any picture on your screen, change the output resolution to a
lower one (1080i for example if your display is HD-Ready but not Full-HD compatible). If the DreamScaler 4 is
configured to output on its Analog output, go throw steps 1 to 5 to change the active output to HDMI.
1) Press the Menu button on the front panel of the DreamScaler 4 once. You should see ‘Main Menu /Input Select’
on the FPD.
2) Press the Up button once. You should see ‘Main Menu / Output Setup’ on the FPD.
3) Press the Enter button. You should see ‘Output Setup / Analog/Digital’ on the FPD.
4) Press the Enter button. You should see ‘Analog/Digital / BNC (Analog)’.
5) Press the Down button to select ‘HDMI (Digital)’ and press the Enter button.
Displays with a Component (YPbPr) Input
1) Press the Menu button on the front panel of the DreamScaler 4 once. You should see
2) ‘Main Menu / Input Select’ on the FPD.
3) Browse to ‘Main Menu / Output Setup’ sub-menu on the FPD.
4) Press the Enter button. You should see ‘Output Setup / Analog/Digital’ on the FPD.
5) Press the Enter button once again. You should see ‘Analog/Digital / BNC (Analog)’. If you don’t, press the Up
button once and the press Enter. You should see ‘Output Setup / Analog/Digital’ on the FPD.
6) Browse to ‘Output Setup / Color Space’ sub-menu on the FPD.
7) Press the Enter button once. You should see ‘Color Space / YPbPr’ on the FPD. If you don’t, press the Up but-
ton once and press Enter. You should see the DreamScaler 4’s on screen Display (OSD) on your screen.
The DreamScaler 4 cannot output a component signal if the input signal is from a DVI or HDMI source with
HDCP. Instead the DreamScaler 4 outputs a blue screen.