background image

- 15 -

 

 

3.1.2

 

TEMPERATURE SETTING 
 

Water  temperature  se  is  set  by  turning  the  thermostat  knob.  The  desired  symbol  is  adjusted against  the 
fixed point on the control panel (Figure 6). 

 

                               

 

 

                                  

 

Figure 6 

 

Adjusting the thermostat selector at the left backstop does not mean permanent shutoff of 
the heating element. When the storage tank is in use without blocking the daily rate, we do 
not recommend the temperature to be set above 65°C. The maximum value to select is 

„55“

 

 

3.2

 

MOST FREQUENT FUNCTION FAILURES AND THEIR CAUSES 

 

DEFECT 

CONTROL LIGHT 

FAILURE 

Water in the tank is cold

 

 

Is on 

 

Heating element failure 

Water in the tank is not 
warm enough

 

 

is on

 

 

Failure of one of the heating 
coils in the element 

Water in the tank is cold 

 

is not on 

 

Thermostat failure 

 

The safety fuse turned off 
electricity supply 

 

Power supply outside the 
storage tank discontinued 

Water in the tank does 
not correspond with 
temperature set 

 

is on

 

 

Thermostat failure 

Table 3 

 

Lower  temperature  range 
(about 5°C) 

Fixed  point  on  the  control 
panel 

„Anti-freezing“ 
temperature (about 8°C) 

 

pevný  bod  na  ovládacím 
panelu 

 

teplota „proti zamrznutí“ 

(kolem 8°C) 

Upper temperature range 
(about 74°C) 

 

„Ideal“ temperature (about 
55°C) 

 

 

„optimální“ teplota  

(kolem 60°C) 

 

Содержание OKCE 100 NTR


















Отзывы: