background image

Contents

Overview 

LightBloc FlexShade Components .................................................1

Please Read 

Warnings and Safety Information  ..................................................2

Please Read 

Field Adjustments, Cleaning and Maintenance  ............................2

Section 1 

Preparation for Installation .............................................................3

Section 2 

Side Channels ..................................................................................4

Section 3 

Check Shade Fabric ........................................................................4

Section 4 

Bead Chain Limits and Safety Device Installation  

(for Units with Clutch or Spring Roller Operation)

 ......................5

Section 5 

Check Shade Operation  

(for Units with Clutch or Spring Roller Operation)

 ......................5

Section 6 

Electrical Connections  

(for Motorized Units)

 .......................................................................6

Section 7 

Wiring Diagrams  

(for Motorized Units)

 .......................................................................6

Section 8 

Limit Switch Adjustments  

(for Motorized Units)

 .......................................................................7

Section 9 

Dimensions - LightBloc FlexShade ................................................8

 CAUTION 

Read and understand all warnings 

(Page 2 of this document)

 before beginning installation.

Overview -

 LightBloc FlexShade Components

TOOLS  
REQUIRED

PENCIL

POWER DRILL

TAPE MEASURE

LEVEL

MALLET

HARDWARE

 (by others) 

If you have any difficulties installing or servicing your  
LightBloc FlexShade, call your dealer or Draper, Inc. 

Side channel - Includes ¾" x 1" 
adjustable mounting angles 

(Mounting angles provided for 
"Inside" or "Jamb"mount installations. 
For "Face Mount" applications, 
Draper provides 

3

/

8

" access holes in side 

channels with plastic plug covers.)

Sill channel -

see details

Fabric grommet

SILL CHANNEL

Inside Mount

1

3

/

8

" H x ¾" D

Face Mount

2¾" H x ¾" D

Face/bottom

cover

(STANDARD)

Side channel

Clutch

Endcap

Motor 

Endcap

Channel

locator

Fabric guide

Top/Back Cover

(STANDARD)

Endcap

Covers

Motor

Shade
fabric

Stays

Slat bar

Roller

Crank Endcap

& Assembly

Crank 

Handle

CRANK ASSEMBLY

Gudgeon assembly

Retainer clip

Idler endcap

fastens to ceiling,

face or jamb

Channel 

Liner

Fabric

Retainer

Endcap

Cover

Draper, Inc.  |  411 S. Pearl St. Spiceland, IN 47385 

draperinc.com  |  765.987.7999  |  800.238.7999  

© 2018 All Rights Reserved 

FORM: LBFS_Inst_18

LightBloc FlexShade

®

INSTRUCTIONS

INSTALLATION & OPERATION

Содержание LightBloc FlexShade









Отзывы: