Caution:
-
All switches must be in “off”
position before adjusting limit
switches.
-
Be prepared to shut off
manually while testing.
-
Shade may be damaged by
running shade fabric down
too far to expose roller.
-
If using a group control system,
each limit switch must be set
prior to connecting to system.
-
Motor must be installed so limit
switches are pointed down.
Section 8 -
Limit Switch Adjustments
(for Motorized Units)
Section 8.1 - Standard and Quiet Motors
(All procedures shown are for Standard Roll. Invert orientation for Reverse Roll)
Section 8.1.1- Push Button Limits
1.
Fully depress both limit switch push buttons, then
operate wall switch to ensure system works properly.
2.
Raise shade to desired “up” stop position.
3.
Set upper limit by depressing proper
(back)
push button.
4.
Lower shade to desired “down” stop position.
5.
Set lower limit by depressing proper
(front)
push button.
Section 8.1.2 - Screw-Type Limits
1.
Determine which direction of fabric travel corresponds
with arrows on motor.
2.
Operate shade to desired “down” stop position.
Set limit by turning proper socket toward “+”
to lower limit, and “-” to raise it.
3.
Operate shade to desired “up” stopping position. Set limit by turning proper screw
toward “-” to raise limit, and “+” to lower it.
Section 8.2 - Limit Adjustments
(RS485 Motors)
For limit setting instructions on these motors, see instructions packaged
with RS485 Address/Limit Setting Tool
(part# C156.241)
.
Section 8.3 - Limit Switch Adjustments—RTS Motors
Section 8.3.1 - Programming Instructions
1.
Connect power to one motor. Select a transmitter channel to assign motor. Hold UP & DOWN buttons until motor jogs, then release.
2.
Check motor direction. To reverse motor direction, hold MY/STOP button for 5 seconds until motor jogs. Check direction again.
Please Note:
Failure to complete Step 2 before Step 3 can only be corrected with a motor reset
(Section 8.3.6)
.
3.
Move motor to upper limit position. Hold MY/STOP & DOWN buttons until motor moves down, then release.
Stop shade at desired lower limit position using MY/STOP button
(shade will not stop on its own)
.
UP and DOWN buttons can be used to adjust the lower limit position if needed.
4.
While motor is at lower limit, hold UP & MY/STOP buttons until motor moves up, then release.
The shade should move to upper limit and stop.
5.
Next, hold MY/STOP button for five seconds until motor jogs.
6.
Put motor into USER MODE by pressing small programming button
(Fig. 13)
on back of transmitter until motor jogs.
7.
Disconnect power to this motor and move to next motor in installation and start with step 1.
8.
Reconnect motor to power when all motors are programmed.
Section 8.3.2 - Setting an Intermediate Stop
-
Shade MUST BE in USER mode.
1.
Move shade to desired mid-point location and hold MY/STOP button until motor jogs.
2.
To test, press MY/STOP button when motor is standing still. Shade will move to that intermediate location.
3.
To delete an intermediate stop, go to intermediate stop and hold MY/STOP button until motor jogs.
Section 8.3.3 - Add a Channe
l - Shade MUST BE in USER mode.
1.
Select channel currently operating motor, then hold programming button until motor jogs.
2.
Select new channel to add to motor, then hold programming button until motor jogs.
3.
The motor should now work on both old and new channel.
Section 8.3.4 - Delete a Channel
- Shade MUST BE in USER mode.
1.
Select channel operating motor that you want to keep, then hold programming button until motor jogs.
2
Select channel to remove, then hold programming button until motor jogs.
Motor should now only work on channel kept from Step 1.
Section 8.3.5 - Adjust Limits in User Mode
1.
Move motor to limit
(upper or lower)
to be changed. Shade must move to previously set limit and will stop automatically.
2.
Hold UP & DOWN buttons until motor jogs.
3.
Move motor to its new limit location and hold MY/STOP button until motor jogs.
Section 8.3.6 - Reset Motor
1.
Disconnect power for 5 seconds and reconnect to power for 15 seconds. Disconnect power for 5 seconds, then reconnect to power and leave connected.
Shade should roll down a few inches and stop.
2.
Hold programming button
(Fig. 13)
for 15 seconds. Motor will jog up and down once; pause and then jog a 2nd time.
Motor is now reset and ready to be programmed.
Figure 12
GLASS SIDE
ROOM SIDE
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
Front
Back
Bottom View
Side View
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
PUSH BUTTON LIMITS
Standard right-hand
motor configuration shown
SCREW-TYPE LIMITS
Standard right-hand
motor configuration shown
BACK
Programming
Button
BACK
Pen
Channel
Selector
UP
STOP
DOWN
LED Lights
BACK
Programming
Button
BACK
Pen
Channel
Selector
UP
STOP
DOWN
LED Lights
Figure 13
page 7 of 8
LightBloc FlexShade
®
