Setup and Programming / Software Flow Chart 9
Programming and viewing of the various setup and
operating parameters is accomplished using the front panel
back lit, two line, sixteen character wide LCD along with the
two LEFT and RIGHT SELECT buttons and the five LEFT,
RIGHT, UP, DOWN and ENTER buttons. The name of the
parameter is on the top line of the display and the setting
value is on the bottom line.
To observe a certain parameter setting without intending to
change its value, just use the LEFT and RIGHT SELECT
buttons and the LEFT and RIGHT arrow buttons to navi-
gate through the menus shown in the software flow chart
below. The current setting for each parameter is shown on
the bottom line of the display. Note that depending upon
certain settings, some screens are not needed and will be
skipped.
To make a change in the displayed parameter and its setting and
if this is the initial setup, you will want to enter the ‘adjust’ mode.
To do this, press the ENTER button that is located in the center
of the four arrow buttons and hold in for several seconds until
the display begins to flash. After you are in the adjust mode
(bottom line of screen flashing) use the left and right arrows to
navigate among screens and use the up and down arrows to
change the parameter setting. When ENTER is pressed, the
new settings will be loaded and stored and the unit will exit the
‘adjust’ mode. You may wish to not press ENTER until you have
gone through all screens and settings and then press ENTER to
save and load all changes in one step OR you can store just one
or several parameters at a time and reenter adjust mode to set
the next. Either method is acceptable.
SETUP:
UNIT ID
RS-232
BAUDRATE
NORMAL MODE
MEQ1000
MULTIPLEX
SETUP INPUT A:
DTD1000
SETUP INPUT B:
DTD1000
CHANMAP
DTD1000
CHANNEL
DTD1000
MODE
Tuner
AGC
DTD1000
Lock Status
NORMAL MODE
MODE:
DTD1000
CHANNEL:
DTD1000
CHANMAP:
DTD1000
Demodulator
BROADCAST
CATV
IRC
HRC
1 - 158
VSB-8
QAM-64B
QAM-256B
ADJUST MODE
ASII MODULE
MAJOR
TABLE
VCT
PROGRAMS
MPEG
INPUT B
BAUDRATE
RS232
UNIT ID
Select
0 - 63
19200
9600
4800
2400
OFFSET
SELECT ALL PROGS
SELECT PROGRAMS
PSIP
OUTPUT CHANNEL
CHANNEL
ADJUST MODE
MULTIPLEX
USE A INPUT ONLY
USE B INPUT ONLY
ENABLED
0 - 90
ENABLED
BASIC MGT/VCT
DISABLED
CVCT
TVCT
USER DEFINED
ORIGINAL CHANNEL
QAM
MODE
QAM-16A
QAM-32A
QAM-64A
QAM-128A
QAM-256A
QAM-512A
ITU-A
QAM-1024A
QAM-64B
QAM-256B
QAM-1024B
ITU-B
SYMRATE
QAM
1.000 -
7.000
CHANNEL
OUTPUT
OUTPUT
CHANMAP
INTERLEAVER
OUTPUT
FORMAT
NORMAL
PRBS15
PRBS15M
PRBS23
PRBS 23M
CW
BROADCAST
CATV
IRC
HRC
1 - 158
RF
LEVEL
45 - 62 dBmV
QAM
PRESET
MANUAL
SYMRATE
GRAY
ENCODING
selected.)
appears only
(This screen
if ITU-A is
DAVIC
DVB
CHANNEL
PSIP
OFFSET
INPUT B
MPEG
PROGRAMS
VCT
TABLE
MAJOR
QAM
MODE
ENCODING
GRAY
QAM
SYMRATE
PRESET
QAM
SYMRATE
Mbits/S
INTERLEAVER
LEVEL
RF
FORMAT
OUTPUT
CHANMAP
OUTPUT
OUTPUT
CHANNEL
ENTER
SELECT
if ITU-A is
(This screen
appears only
selected.)
(These screens only appear if MULTIPLEX is ENABLED.)
(These screens only appear if MULTIPLEX is ENABLED.)
Indicates that ASII module is installed.
ASII module has no adjustments.
This chart assumes a
DTD1000 module or a
SDE24 module in
Input - A and an ASII
module is in Input - B.
This could be different.
FORMAT
BITRATE:
RESOLUTION
VIDEO
NORMAL MODE
BITRATE:
FORMAT
VIDEO
S-VIDEO
COMPOSITE
MPEG2
MPEG4 H.264
1 - 8 Mbits/S
PROGRAM MODE
RESOLUTION
720 x 480
704 x 480
528 x 480
480 x 480
352 x 480
353 x 240
BRIGHTNESS
BRIGHTNESS
0 - 255
CONTRAST
0 - 255
CONTRAST
SATURATION
HUE
MAX AUDIO IN
AUDIO GAIN
AUDIO GAIN
MAX AUDIO IN
HUE
SATURATION
0 - 255
0 - 255
1 Vrms
2 Vrms
MUTE
+ 15 dB to
-15 dB in
1 dB steps
(This screen only appears
for Encoder 1 in a given
SDE24 module. Encoder 2
in that module is always
forced to MPEG2.)
SETUP INPUT A:
SDE24
I128, J1
I128, J2
I64, J2
I128, J3
I132, J4
I128, J4
I16, J8
I128, J5
I8, J16
I128, J6
I4, J32
I128, J7
I2, J64
I128, J8
I1, J128
(This screen
appears only
if ITU-B
is selected.)
AUDIO
ENCODE:Exx
AUDIO
ENCODE:Exx
AC3
MP2
