background image

6

Instructions for use

  |  

Dräger BG ProAir

  

Safety-related information 

1 Safety-related 

information

– Before using this product, carefully read these instructions 

for use and those of the associated products.

– Strictly follow the instructions for use. The user must fully 

understand and strictly observe the instructions. Use the 

product only for the purposes specified in the intended use 

section of this document.

– Failure to use the product as described in these 

instructions for use can lead to reduced protection.

– Do not dispose of the instructions for use. Ensure that they 

are stored and used appropriately by the product user.

– Only trained and competent users are permitted to use 

this product.

– Comply with all local and national rules and regulations 

associated with this product.

– Only trained and qualified personnel are permitted to 

inspect, repair and service the product as detailed in these 

instructions for use (see "Maintenance", page 14). Further 

maintenance work that is not detailed in these instructions 

for use must only be carried out by Dräger or personnel 

qualified by Dräger. Dräger recommend a Dräger service 

contract for all maintenance activities. 

– Use only genuine Dräger spare parts and accessories. 

Otherwise, the proper functioning of the product may be 

impaired.

– Notify Dräger in the event of any component fault or 

failure.

– Do not use a faulty or incomplete product. Do not modify 

the product.

Conventions in this document

2.1 Meaning 

of 

the warning notices

The following warning notices are used in this document to 

alert the user to potential hazards. The meanings of the 

warning notices are defined as follows:

2.2 Trademarks

The following website lists the countries in which the 

trademarks from Dräger are registered: 

www.draeger.com/trademarks.

The trademarks listed are only registered in certain countries 

and not necessarily in the country in which this document is 

published.

3 Description

3.1 Product 

overview

See overview graphic at the start of the instructions:

Warning 

sign

Signal word

Classification of the warning 

notice

WARNING

Indicates a potentially hazard-

ous situation. If not avoided, it 

could result in death or serious 

injury.

CAUTION

Indicates a potentially hazard-

ous situation. If not avoided, it 

could result in physical injury. It 

may also be used to alert 

against unsafe practices.

NOTICE

Indicates a potentially hazard-

ous situation. If not avoided, it 

could result in damage to the 

product or environment.

Trademark

Trademark owner

Bluetooth

®

Bluetooth SIG, Inc.

1

Exhalation hose

2

Connecting piece with protective cap

3

Bayonet ring

4

Inhalation hose

5

Bypass hose (red)

6

Medium-pressure hose to sensor unit (blue)

7

Medium-pressure hose for the oxygen supply (blue)

8

Carrying frame

9

Buddy-light

10

Onboard electronics (sensor unit)

11

Breathing air cooler

12

Minimum valve

13

Relief valve (under the spring bridge)

14

Breathing bag

15

Pressure reducer incl. hand wheel

16

Hand wheel of cylinder valve

17

Pressure indicator on cylinder valve

18

Bypass button

19

Cylinder strap

20

Drainage valve (between carrying frame and com-

pressed oxygen cylinder)

21

Compressed oxygen cylinder

22

Spring bridge

23

Locking lever

24

CO

2

 absorber

25

Lid

26

Window for buddy-light

27

Connect ECU ("Electronic Control Unit")

27-1

Graphical pressure display

27-2

Cylinder pressure

Содержание BG ProAir



































Отзывы: