background image

 

 CALL 

TOLL-FREE 

1-800-DR-OWNER         

37

 

 

CHAPTER 6

 

TROUBLESHOOTING

 

 

Most problems are easy to fix.  Consult the Troubleshooting Table below for common problems and their 
solutions.  If you continue to experience problems call Country Home Products, Inc. for support. 

 

Troubleshooting Table 

 
 
 

BEFORE PERFORMING ANY MAINTENANCE PROCEDURE, STOP THE ENGINE AND

 

DISCONNECT THE 

SPARK PLUG WIRE.

 

 

 

S

YMPTOM

 

P

OSSIBLE 

C

AUSE

 

Recoil will not pull 
out or is difficult to 
pull. 

⇒ 

Check that the Blade Control Lever is properly adjusted and in the released 
position. 

⇒ 

Check the Engine oil level, the Engine may be seized. 

⇒ 

There may be an oil compression lock in the Cylinder.  Take out the Spark Plug; 
hold a rag over the Spark Plug hole and pull the Recoil Cord several times to blow 
out any oil in the Cylinder.  Wipe off the Spark Plug and reinstall it. 

⇒ 

The Recoil may be broken or jammed.  Call 1-800-DR-OWNER (376-9637) for 
assistance.

 

The Engine will not 
start. 

 

(Please refer to the 
Engine Owner’s 
Manual for Engine-
specific procedures.)

 

⇒ 

Make sure the Spark Plug Wire is attached. 

⇒ 

Make sure the Key is in the START position. 

⇒ 

If the Engine is cold, push the Primer Bulb 3 to 4 times.  See page 16. 

⇒ 

The gas must be fresh and clean.  If the gas is old, change it.  Use a fuel stabilizer 
if you keep gas longer than one month. 

⇒ 

Check the Throttle adjustment and travel. 

⇒ 

The Blade Engagement Control Lever must be in the down position. 

⇒ 

Make sure that the Spark Plug is clean.  If the Spark Plug is dirty or cracked, 
change it.  If it’s oily, leave it out, hold a rag over the Plug hole and pull the Recoil 
Cord several times to blow out any oil in the Cylinder, then wipe off the Plug and 
reinsert it. 

⇒ 

Make sure that the wiring is all connected and the connections are tight. 

⇒ 

If your Engine still will not start, call 1-800-DR-OWNER (376-9637) for assistance.

Содержание SCOUT FIELD and BRUSH MOWER























































Отзывы: