background image

 

 

CALL TOLL-FREE 

1-800-DR-OWNER         

9

 

 

THE MOWER MUST BE OPERATED SAFELY TO PREVENT OR MINIMIZE THE RISK OF MINOR OR 
MODERATE INJURY.  UNSAFE OPERATION CAN CREATE A NUMBER OF HAZARDS FOR YOU.  ALWAYS 
TAKE THE FOLLOWING PRECAUTIONS WHEN OPERATING THIS MOWER:

 

• 

KEEP IN MIND THAT THE OPERATOR OR USER IS RESPONSIBLE FOR ACCIDENTS OR HAZARDS 
OCCURRING TO OTHER PEOPLE, THEIR PROPERTY, AND THEMSELVES.

 

• 

USE EAR PROTECTORS OR EAR PLUGS RATED FOR AT LEAST 20 DBA TO PROTECT YOUR HEARING.

 

• 

WEAR LONG PANTS WHILE MOWING.

 

• 

USE CAUTION WHEN MOWING CLOSE TO FENCES, BUILDINGS, TREES, ETC. SO AS NOT TO HIT THE 
HANDLE BAR.  DOING SO, YOU MAY INJURE YOUR HAND OR LOSE CONTROL OF THE MACHINE.

 

• 

SEE MANUFACTURER’S INSTRUCTIONS FOR PROPER OPERATION AND INSTALLATION OF 
ACCESSORIES.  ONLY USE ACCESSORIES APPROVED BY COUNTRY HOME PRODUCTS, INC.

 

• 

KEEP ALL NUTS AND BOLTS TIGHT, ESPECIALLY THE BLADE ATTACHMENT BOLTS, AND KEEP THE 
EQUIPMENT AND ATTACHMENTS IN GOOD OPERATING CONDITION. 

• 

THE MOWER BLADE IS SHARP AND CAN CUT.  WRAP THE BLADE OR WEAR GLOVES, AND USE EXTRA 
CAUTION WHEN SERVICING. 

• 

NO LIST OF WARNINGS AND CAUTIONS CAN BE ALL-INCLUSIVE.  IF SITUATIONS OCCUR THAT ARE 
NOT COVERED BY THIS MANUAL, THE OPERATOR MUST APPLY COMMON SENSE AND OPERATE 
THIS MOWER IN A SAFE MANNER.  CALL 1-800-DR-OWNER (376-9637) FOR ASSISTANCE. 

 

A Note to All Users 

Under California law, and the laws of some other states, you are not permitted to operate an internal 
combustion engine using hydrocarbon fuels without an engine spark arrester.  This also applies to operation 
on US Forest Lands.  All DR SCOUT FIELD and BRUSH MOWERS shipped to California and Washington 
State are provided with spark arresters.  Failure of the owner/operator to maintain this equipment in 
compliance with state regulations is a misdemeanor under California law and may be in violation of other 
state and/or federal regulations.  Contact your local fire marshal or forest service for specific information in 
your area. 

Additional Information and Potential Changes 

Country Home Products, Inc. reserves the right to discontinue, change, and improve its products at any time 
without notice or obligation to the purchaser.  The descriptions and specifications contained in this manual 
were in effect at printing.  Equipment described within this manual may be optional.  Some illustrations may 
not be applicable to your machine. 

 

Содержание SCOUT FIELD and BRUSH MOWER























































Отзывы: