background image

6

 

        

DR

® 

K10 RAPIDFIRE™ LOG SPLITTER

 

California Proposition 65: 

 

This product contains or emits chemicals known to the state of California to cause cancer, birth defects, and other 
reproductive harm. 

General Safety 

California Proposition 65 

A Note to All Users  

No list of warnings and cautions can be all-inclusive.  If situations occur that are not covered by this manual, the operator must 
apply common sense and operate this DR K10 RAPIDFIRE LOG SPLITTER in a safe manner.  Contact us at www.DRpower.com or 
call 1-800-DR-OWNER (376-9637) for assistance. 

Operating this Log Splitter safely is necessary to prevent or minimize the risk of death or serious injury.  Unsafe operation can 
create a number of hazards for you.  Always take the following precautions when operating this Log Splitter: 

 

Your Log Splitter is a powerful tool, not a plaything.  Exercise extreme caution at all times.  The machine is designed to split 
logs.  Do not use it for any other purpose. 

 

Know how to stop the Log Splitter quickly; see “stopping the motor” in chapter 3. 

 

Never operate your unit on a slippery, wet, muddy, or icy surface.  Exercise caution to avoid slipping or falling. 

 

See manufacturer’s instructions for proper operation and installation of accessories.  Only use accessories approved by DR 
Power Equipment. 

 

Never use the machine without ensuring that all guards and shields are in place. 

 

Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the Log Splitter.  This includes 
all shields and guards.  Modifications to your machine could cause personal injuries and property damage and will void your 
warranty. 

 

Allow only one person to operate the Log Splitter at any time. This includes placing the log on the beam. 

 

If the machine should start making an unusual noise or vibration, Shut off the Motor, Unplug the Power Cord.  Wait 5 
minutes for machine to cool down then inspect for damage.  Vibration is generally a warning of trouble.  Check for damaged 
parts and clean, repair and replace as necessary. 

 

Never tamper with safety devices.  Check their proper operation regularly. 

 

Before performing any maintenance or inspection procedure on the Log Splitter, Shut off the Motor, Unplug the Power Cord.  
Wait 5 minutes for machine to cool down. 

 

Never allow people who are unfamiliar with these instructions to use the Log Splitter.  Allow only responsible individuals who 
are familiar with these rules of safe operation to use your machine. 

 

Never overload or attempt to split logs beyond the recommendations listed in this manual.  Personal injury or damage to the 
machine could result. 

 

While using the Log Splitter, don't hurry or take things for granted.  When in doubt about the equipment or your surroundings 
stop the machine and take the time to look things over. 

 

Never operate the machine when under the influence of alcohol, drugs, or medication. 

 

Use the machine only in daylight. 

 

Stay alert for hidden hazards or traffic. 

 

Keep all nuts and bolts tight and keep the equipment in good operating condition.  

Содержание K10 RAPIDFIRE

























Отзывы: