manualshive.com logo in svg

DPCAV ShutterBug Pro, Инструкция по эксплуатации

Поделиться
Скачать
DPCAV ShutterBug Pro Скачать руководство пользователя страница 8

ShutterBug Pro © 2007-2013

Page 8

Sep-15-2013

S

TART OF 

P

ROGRAMMING

Programming begins by holding down the pushbutton switch while you apply power to
ShutterBug Pro. Continue to press the switch until the Red LED is on. When you are
ready start programming, release the switch. Now the fun begins!

Step 1: 

Ž

 

Camera Wake-up/Standalone Interval.

Range: 1 = Turn Off, else 2 - 120

Depending on the operating mode, the Wake-up/Standalone interval is used to
prevent the camera’s power save feature from putting the camera to sleep or to
determine the time between snapshots.

W

AKE

-

UP

While in the R/C or external trigger mode (see Step 4), this is the delay time
before the next shutter “Keep Awake” movement. At the time interval you choose,
the Stage 1 (focus) position will be active for a moment, which keeps the camera
awake. So, to prevent your digital camera from falling asleep, set this time to be
less than the camera’s maximum allowed inactivity duration. For example, if your
camera turns itself off in five minutes, then enter four presses and choose
“Minutes” in Step-2 (for four minutes). If it turns off in 60 seconds, then enter five
presses and choose “10X Seconds in Step-2 (for fifty seconds).

S

TANDALONE

When in the Standalone mode, this is the time delay before the next snapshot.
If you want to take a photo every five minutes, enter five presses and choose
“Minutes” in Step-2 (for five minutes). If you want a photo every two hours, enter
two presses and choose “Hours” in Step-2.

IMPORTANT NOTE: Standalone mode is automatically disabled if a R/C servo
signal has been detected. To test standalone mode after programming you must
disconnect battery power, remove the servo signal source, then reapply power.

Step 2: 

ŽŽ

  Camera Wake-up/Standalone Interval Units.

Range: 1= Seconds, 2= 10x Seconds, 3= Minutes, 4= Hours.

This entry is a companion to Step 1. It sets the time units (resolution) for the
Camera Wake-up/Standalone Interval. For example, press three times for
minutes.

Содержание ShutterBug Pro

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды