manualshive.com logo in svg

DPCAV ShutterBug Pro, Инструкция по эксплуатации

Поделиться
Скачать
DPCAV ShutterBug Pro Скачать руководство пользователя страница 4

ShutterBug Pro © 2007-2013

Page 4

Sep-15-2013

Figure 7, Basic Direct Connect ID

Figure 8, 2-Wire Layout

Figure 9, 4-wire Layout

The photo on the right shows how the two camera
stages are identified on ShutterBug Pro’s circuit board.
The connections must be made by soldering your
custom made wiring cable to the indicated pads. Use a
temperature controlled soldering iron set for delicate
soldering work.

The Stage-1 and Stage-2 switches are polarity
sensitive. So, they must be wired to match the polarity
of your camera. This can be determined by using a voltmeter across the camera’s shutter
button (switch) contacts during its resting state.

Direct Connect Method: 

2-Wire

Not all cameras do a focus when the shutter
button is depressed. Or perhaps you do not
want to use the cameras auto focus feature. If
so, only two wires are needed. 

N/A

Not Used

SHUT+

Shutter Positive

SHUT-

Shutter Negative

Direct Connect Method: 

4-Wire

Typical wiring for a camera that has an auto
focus stage is accommodated with the 4-wire
scheme.

FOC+

Focus Positive

FOC-

Focus Negative

SHUT+

Shutter Positive

SHUT-

Shutter Negative

Содержание ShutterBug Pro

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды