Dover PSG Wilden Pro-Flo SHIFT PS420 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 28

Dover PSG Wilden Pro-Flo SHIFT PS420 Скачать руководство пользователя страница 11

WIL-11500-E-11

11

PS420/430 Bolted Metal

PS420/PS430 METAL
SUCTION LIFT

CAPABILITY

Suction-lift curves are calibrated for pumps

operating at 305 m (1,000') above sea level.
This chart is meant to be a guide only. There

are many variables that can affect your

pump's operating characteristics. The number
of intake and discharge elbows, viscosity of

pumping fluid, elevation (atmospheric
pressure) and pipe friction loss all affect the

amount of suction lift your pump will attain.

PS420/PS430 STAINLESS

STEEL SUCTION LIFT
CAPABILITY

Suction-lift curves are calibrated for pumps
operating at 305 m (1,000') above sea level.

This chart is meant to be a guide only. There
are many variables that can affect your

pump's operating characteristics. The number
of intake and discharge elbows, viscosity of

pumping fluid, elevation (atmospheric

pressure) and pipe friction loss all affect the
amount of suction lift your pump will attain.

SUCTION LIFT CAPABILITY

«
...
9
10
11
12
13
...
»

Содержание PSG Wilden Pro-Flo SHIFT PS420





























Отзывы:

Нет отзывов