Dover PSG Wilden Pro-Flo SHIFT PS420 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Dover PSG Wilden Pro-Flo SHIFT PS420 Скачать руководство пользователя страница 10

WIL-11500-E-11

10

PS420/430 Bolted Metal

PS420/PS430 METAL
FULL-STROKE

PTFE-FITTED

Ship Weights…420 Threaded AL 26 kg (57 lb)

420 Threaded SS 50 kg (111 lb)

420 Threaded Iron 39 kg (86 lb)

430 Flanged AL 28 kg (62 lb)

430 Flanged SS 53 kg (116 lb)

430 Flanged Iron 42 kg (92 lb)

Air Inlet……………………………………….3/4"

Inlet……………………………...38 mm (1-1/2")

Outlet……………………………38 mm (1-1/2")

Suction Lift………………..5.2 m Dry (17.0

′

) AL

9.0 m Wet (29.5

′

) AL

3.5 m Dry (11.4

′

) SS

9.0 m Wet (29.5

′

) SS

4.1 m Dry (13.6

′

) Iron

9.3 m Wet (30.6

′

) Iron

Disp. per Stroke

1

….……….1.1 L (0.30 gal) AL

0.9 L (0.24 gal) SS

0.9 L (0.24 gal) Iron

Max. Flow Rate……………485 lpm (128 gpm)

Max. Size Solids…………………6.4 mm (1/4")

1

Displacement per stroke was calculated at 4.8

bar (70 psig) air inlet pressure against a 2.1 bar

(30 psig) head pressure.

Example:

To pump 280 lpm (74 gpm) against

a discharge head of 2.1 bar (30 psig) requires

5.5 bar (80 psig) and 88 Nm

3

/h (52 scfm) air

consumption.

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps
should be specified so that daily operation parameters will fall in the center of the pump's performance curve.

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

PERFORMANCE

«
...
8
9
10
11
12
...
»

Содержание PSG Wilden Pro-Flo SHIFT PS420





























Отзывы:

Нет отзывов