manualshive.com logo in svg

Dover PSG Wilden Pro-Flo P220/AAPPP, Инструкция по эксплуатации и техническому обслуживанию, Страница: 9 / 28

Поделиться
Скачать
Dover PSG Wilden Pro-Flo P220/AAPPP Скачать руководство пользователя страница 9

 

WIL-11570-E-04  

9 

P220/230 Bolted Metal 

 

SECTION 5 

 

P220/P230 METAL 
RUBBER-FITTED

 

 

 

Ship Weights……….…Aluminum 11 kg (24 lb) 

Ductile Iron 21 kg (47 lb) 

316 Stainless Steel 23 kg (51 lb) 

Air Inlet………………………..……………..1/4" 

Inlet…...…………………...…………25 mm (1") 

Outlet………………...………………25 mm (1") 
Suction Lift……………………5.4 m Dry (17.6’) 

9.3 m Wet (30.6’)  

Disp. per Stroke

1

……...….......0.30L (0.08 gal) 

Max. Flow Rate……………..212 lpm (56 gpm) 

Max. Size Solids…………………6.4 mm (1/4") 

 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

 

 

Example:

 To pump 56.8 lpm (15 gpm) 

against a discharge head of 3.3 bar (48 psig) 

requires 4.1 bar (60 psig) and 34 Nm

3

/h (20 

scfm) air consumption. 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

 

 

P220/P230 METAL 

TPE-FITTED

 

 

 
Ship Weights……….…Aluminum 11 kg (24 lb) 

Ductile Iron 21 kg (47 lb) 

316 Stainless Steel 23 kg (51 lb) 

Air Inlet………………………..……………..1/4" 

Inlet…...…………………...…………25 mm (1") 

Outlet………………...………………25 mm (1") 

Suction Lift……………………4.1 m Dry (13.6’) 

9.3 m Wet (30.6’)  

Disp. per Stroke

1

……...….......0.34L (0.09 gal) 

Max. Flow Rate……………..212 lpm (56 gpm) 

Max. Size Solids…………………6.4 mm (1/4") 

 
 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

 

 

Example:

 To pump 273 lpm (72 gpm) against 

a discharge head of 2.8 bar (40 psig) requires 

5.5 bar (80 psig) and 83 Nm

3

/h (49 scfm) air 

consumption.

 

 

 

 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

 

 

 

 

PERFORMANCE 

Содержание PSG Wilden Pro-Flo P220/AAPPP





























Отзывы:

Нет отзывов