Dover PSG Wilden Pro-Flo P220/AAPPP Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 28

Dover PSG Wilden Pro-Flo P220/AAPPP Скачать руководство пользователя страница 16

WIL-11570-E-04

16

P220/230 Bolted Metal

Step 4

Step 5

Step 6

Remove the discharge valve balls, seats
and valve seat O-rings from the discharge
manifold and liquid chamber, inspect for
nicks, gouges, chemical attack or
abrasive wear.

Using a 13 mm (1/2") wrench, remove the

inlet manifold.

NOTE:

Inverting the pump will facilitate

removal of inlet manifold.

Remove the inlet valve balls, seats and

valve seat O-rings from the liquid
chamber and inlet manifold, inspect for
nicks, gouges, chemical attack or
abrasive wear.

Step 7

Step 8

Step 9

Using a 13 mm (1/2") wrench, remove the
liquid chambers from the center section.

The liquid chamber should be removed to

expose the diaphragm and outer piston.
Rotate center section and remove the
opposite liquid chamber.

Using two adjustable wrenches or 25 mm

(1”) sockets, remove diaphragm assembly
from center section assembly.

DISASSEMBLY / REASSEMBLY

«
...
14
15
16
17
18
...
»

Содержание PSG Wilden Pro-Flo P220/AAPPP





























Отзывы:

Нет отзывов