Dover PSG Wilden Pro-Flo P220/AAPPP Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Dover PSG Wilden Pro-Flo P220/AAPPP Скачать руководство пользователя страница 10

WIL-11570-E-04

10

P220/230 Bolted Metal

P220/P230 METAL
REDUCED-STROKE

PTFE-FITTED

Ship Weights……….…Aluminum 11 kg (24 lb)

Ductile Iron 21 kg (47 lb)

316 Stainless Steel 23 kg (51 lb)

Air Inlet………………………..……………..1/4"

Inlet…...…………………...…………25 mm (1")

Outlet………………...………………25 mm (1")

Suction Lift……………………3.5 m Dry (11.4’)

9.3 m Wet (30.6’)

Disp. per Stroke

1

……...….......0.23L (0.06 gal)

Max. Flow Rate……………..168 lpm (44 gpm)

Max. Size Solids…………………6.4 mm (1/4")

1

Displacement per stroke was calculated at 4.8

bar (70 psig) air inlet pressure against a 2.1 bar

(30 psig) head pressure.

Example:

To pump 280 lpm (74 gpm) against

a discharge head of 2.1 bar (30 psig) requires
5.5 bar (80 psig) and 88 Nm

3

/h (52 scfm) air

consumption.

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps
should be specified so that daily operation parameters will fall in the center of the pump's performance curve.

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

P220/P230 METAL
FULL-STROKE

PTFE-FITTED

Ship Weights……Stainless Steel 23 kg (51 lb)

Aluminum 11 kg (24 lb)

Cast Iron 23 kg (47 lb)

Air Inlet………………………..……………..1/4"

Inlet…...…………………...…………25 mm (1")

Outlet………………...………………25 mm (1")

Suction Lift……………………5.5 m Dry (18.2’)

9.0 m Wet (29.5’)

Disp. per Stroke

1

……...….........0.3L (0.08 gal)

Max. Flow Rate……………..185 lpm (49 gpm)

Max. Size Solids…………………6.4 mm (1/4")

1

Displacement per stroke was calculated at 4.8

bar (70 psig) air inlet pressure against a 2.1 bar

(30 psig) head pressure.

Example:

To pump 75.7 lpm (20 gpm)

against a discharge head of 3.1 bar (45 psig)

requires 4.1 bar (60 psig) and 36.9 Nm

3

/h (23

scfm) air consumption.

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps
should be specified so that daily operation parameters will fall in the center of the pump's performance curve.

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.

PERFORMANCE

«
...
8
9
10
11
12
...
»

Содержание PSG Wilden Pro-Flo P220/AAPPP





























Отзывы:

Нет отзывов