Dover PSG Wilden Pro-Flo 230/SSPPP Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

Dover PSG Wilden Pro-Flo 230/SSPPP Скачать руководство пользователя страница 15

WIL-11570-E-03

Wilden

®

15

Disassembly / Reassembly

Pump Disassembly

Tools Required:

•

13 mm (1/2") Box Wrench

•

2

–

25 mm (1") Sockets

or Adjustable Wrench

•

Adjustable Wrench

•

Vise equipped with

soft jaws (such as plywood,
plastic or other suitable material)

CAUTION:

Before any maintenance or repair is attempted, the compressed air line

to the pump should be disconnected and all air pressure allowed to bleed from the
pump. Disconnect all intake, discharge and air lines. Drain the pump by turning it
upside down and allowing any fluid to flow into a suitable container. Be aware of

any hazardous effects of contact with your process fluid.

NOTE:

The model photographed is a metal PX200 25 mm (1") pump. Your specific

pump model may vary from configuration shown; however, pump disassembly
procedure will be the same.

NOTE:

The model used for these instructions incorporates rubber diaphragms and

balls. Models with PTFE diaphragms and balls are the same except where noted.

Step 1

Please note alignment marks on center
section. Use to properly align liquid chamber
to center section.

Step 2

Using a 13 mm (1/2") wrench, loosen
the discharge manifold from the liquid
chambers.

Step 3

Remove the discharge manifold to expose
the valve balls, valve seats and valve seat
O-rings.

Section 7

«
...
13
14
15
16
17
...
»

Содержание PSG Wilden Pro-Flo 230/SSPPP





























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды