background image

 

Rack Monitor 8800E/8801E 
Document: Operation  Manual  
Date: 16-Jun-2011

 

Version: A.6

 

 

 

Page 3 of 35 H71343 

 

Disclaimer 

 

In this document an operation manual is presented of the 

OPW

 Rack Monitor 8800E/8801E. It is important that the 

end user (in many cases the operator) of the 

OPW

 Rack Monitor 8800E/8801E has an adult age, is skilled, reads 

and understands this manual, otherwise it is not recommended to use the 

OPW

 Rack Monitor 8800E/8801E. 

 

OPW Fluid Transfer Group Europe BV

 guarantees that this product is adequate for the stated use and is in 

accordance with the Directive(s) stated in the declaration of conformity in this manual. 
 

OPW Fluid Transfer Group Europe BV

 can not be held responsible for incorrect use of the RACK MONITOR 

8800E/8801E. The Rack Monitor 8800E/8801E is for the use of monitoring of loading of tank trucks with the 
application and parameters stated in this manual.  

In case this OPW Rack Monitor 8800E/8801E is used in another location than mentioned in the initial 
quotation or is abused, all guarantees will be declined.  

 
This operation manual is a part of the supplied product and must at all times accompany the Rack Monitor 
8800E/8801E, when it is relocated or sold to a third party. All pages of this manual should be present, in 
accordance to the table of contents. If not, please contact the 

OPW Fluid Transfer Group Europe BV

 
 
© COPYRIGHT 2007. The design, drawings and documentation are the exclusive property of 

OPW Fluid Transfer 

Group Europe BV

. It is submitted on the condition that the designs contained therein are held confidential and is 

subject to return on demand. 
 
Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by 
means of photography, microfilm, storage in computer files or otherwise, which also applies to full or partial 
processing, without the written consent of 

OPW Fluid Transfer Group Europe BV

 
Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. 
The 

OPW Fluid Transfer Group Europe BV

 therefore accepts no liability, not even for direct or indirect damage, 

occurring due to or in relation with the application of publications issued by 

OPW Fluid Transfer Group Europe 

BV

 
This is an 

OPW Fluid Transfer Group Europe BV

 product, for technical assistance, information and/or complaints 

contact: 

 

OPW Fluid Transfer Group Europe BV

 

 

Visiting adress:                    
Roggestraat 38 
2153 GC  Nieuw Vennep  
Netherlands

 

Postal adress: 
P.O.Box 32 
2150 AA  Nieuw Vennep 
Netherlands 

 
T: +31 (0)252 660 300     
F: +31 (0)252 660 204    
E: 

[email protected]

 

W: 

http://www.opw-ftg.nl

 

 
Mr. Harry Gilde 

Managing Director 

Содержание OPW Fluid Transfer civacon 8800E




































Отзывы: