Dover Anthony 401 Скачать руководство пользователя страница 40

Страница: 40 / 80

Model 401 & 403 Pass-Thru

Service and Installation Instructions

99-21972-S001 Rev. C

- 40 -

www.anthonyintl.com

Cut lead wires to remove.

To replace, re-wire new plug according to color coded wires.

10.

Reverse instructions to replace.

Frame Gasket Replacement

To order replacement gaskets, specify door height & width and manufacture

date. (Date is located between the panes of glass on the aluminum spacer bar
as shown above.)

To remove, pull gasket straight out at top, then slide up and out to remove center

“L” groove in frame plastic.

Start in corner.

Insert bottom half arrow on bottom of frame gasket into

“L” groove in middle

of frame gasket. Then push full arrow on back top of gasket into top groove in
frame plastic.

If necessary, tuck all corners with a flat-head screwdriver.

Содержание Anthony 401

















































































Результаты поиска

Содержание Anthony 401

Отзывы:

Похожие инструкции для Anthony 401

Бренды по названию

Популярные бренды

Dover Anthony 401, Инструкции по обслуживанию и установке

Результаты поиска

Содержание Anthony 401

Отзывы:

Похожие инструкции для Anthony 401

Бренды по названию

Популярные бренды