Lit. No. 96582, Rev. 00
3
April 1, 2016
85200, 96500 CabCommand HAND-HELD CONTROL
Scoop/Retract Blade Positions
The two round buttons located to the left and right of
the RAISE button move both wings at the same time,
into the following blade postions.
Function Description of Operation
SCOOP
Press this button to extend both wings forward
into the scoop position. Function times
out after 5.0 (V‑plow) or 5.5 (WIDE‑OUT)
seconds.
RETRACT
Press this button to draw both wings into the
fully retracted/vee position. Function times
out after 3.0 (V‑plow) or 4.5 (WIDE‑OUT)
seconds.
Wing Positions
The two round buttons located to the left and right of
the LOWER button move either wing independently of
the other, as described below.
Function Description of Operation
L WING
Press this button on the left side of the control
to move the left wing. The first time the button
is pressed after the control is turned ON or
another function is used, the wing will extend.
Repeated use of the same button, without
using another function, results in movement
in the opposite direction from the previous
movement. Function times out after
3.0 (V‑plow), 3.75 (WIDE‑OUT – OUT) or
3.25 (WIDE‑OUT – IN) seconds.
R WING
Press this button on the right side of the
control to move the right wing. The first time
the button is pressed after the control is
turned ON or another function is used, the
wing will extend. Repeated use of the same
button, without using another function, results
in movement in the opposite direction from the
previous movement. Function times out after
3.0 (V‑plow), 3.75 (WIDE‑OUT – OUT) or
3.25 (WIDE‑OUT – IN) seconds.
Control Functions – Multi-Position Blade
Snowplows
Raise, Lower, FLOAT, Angle
Pressing the four diamond‑shaped buttons in the
center of the control face will result in the blade
movements described in the following table.
Function Description of Operation
RAISE
Press this button to raise the blade and cancel
the FLOAT mode. Function times out after
4.0 (V‑plow) or 3.5 (WIDE‑OUT™) seconds.
LOWER
Press this button to lower the blade. Release
the button to stop the blade at the desired
height.
FLOAT*
Press the
LOWER
button and hold 3/4 second
to activate this mode. The FLOAT light in
the upper left corner of the control face will
illuminate. The blade will lower to the ground
surface and follow the contour of the surface
as it dips or raises. Function does not time
out; however, control will shut down after
20 minutes of nonuse.
Press the
RAISE
button momentarily to
cancel FLOAT. Angling left or right will not
interrupt (pause) the FLOAT function.
L
(Angle
Left)
With wings in a straight line, press the
L
button
to move both wings to the angle left position.
The left wing retracts while the right wing
extends (V‑plow). Function times out after 3.0
(V‑plow) or 3.25 (WIDE‑OUT) seconds.
R
(Angle
Right)
With wings in a straight line, press the
R
button
to move both wings to the angle right position.
The right wing retracts while the left wing
extends (V‑plow). Function times out after 3.0
(V‑plow) or 3.25 (WIDE‑OUT) seconds.
*
FLOAT mode activates immediately when the One‑Touch FLOAT
feature is enabled. See the One‑Touch FLOAT section for more
information.
NOTE: If a control function times out before
desired blade movement is complete, release the
button and press it again.
RAISE
ON/OFF
FLOAT
1
2
S C O
O
P
R
E
T
R A C T
LOWER
R
L
3
4
W
IN
G
W I N
G
RAISE
LOWER
R
L
ON/OFF
FLOAT
1
3
2
4
S C O
O
P
R
E
T
R A C T
W
IN
G
W I N
G
FLOAT Light
(green)
