DÖRR EcoGun AL AUTO Скачать руководство пользователя | Manualshive

Страница: 14 / 40

background image

16. Insert spring seat (3).

17. Fit end cap (4). Tighten by hand.

7.3

Maintenance

7.3.1 Maintenance schedule

The maintenance intervals given below are based on experiential values. Adjust maintenance

intervals to the conditions of use.

Interval

Maintenance work

Daily

Check state and tightness of the spray gun as well as

connections and lines.

Check fastening

Check spray gun for material leakage from the housing

bore.

Clean material filter.

Before every change of material

Cleaning

7.2 “Cleaning”.

Monthly

Lubricate piston.

7.3.2 “Lubrication”

After each alteration

Check grounding

4.2 “Assembly”.

7.3.2 Lubrication

Protective equipment:

Protective workwear
Protective gloves

Piston components must be lubricated so

that there will not be any leakages.

Cleaning and maintenance

01/2017

EcoGun AL AUTO - MSG00012EN

14/40

«
...
12
13
14
15
16
...
»

Содержание EcoGun AL AUTO









































Отзывы:

Нет отзывов

Похожие инструкции для EcoGun AL AUTO

Бренд: SAMES KREMLIN Страницы: 30

Бренд: Graco Страницы: 8

CAPspray CS9100

Бренд: SprayTECH Страницы: 17

Бренд: WALTHER PILOT Страницы: 49

Бренд: Goizper Group Страницы: 66

Бренд: Fast Страницы: 104

Бренд: MS Schippers Страницы: 12

Бренд: PAPILLON Страницы: 14

Contractor 288477

Бренд: Graco Страницы: 4

Бренд: Graco Страницы: 34

Бренд: Graco Страницы: 40

Бренд: Hills Страницы: 12

Бренд: DeVilbiss Страницы: 17

Бренд: Titan Страницы: 44

Бренд: Graco Страницы: 78

Бренд: Haussmann Xpert Страницы: 22

Бренд: Tidal Страницы: 8

Бренд: ITW Gema Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды