Dormakaba G-SR EMR Series, Инструкции по ремонту

Страница: 5 / 28

G-SR EMR
5
8
Close both door leaves
À Á
.
Unwind the adjustment sleeve by hand
Â
until pin drops
out
Ã
. In this process, ensure that the clamping plate
remains perpendicular (90°) to the clamping rod .
Secure adjustment sleeve
Ä
.
Note: The pin retains the closing mechanism in its
neutral position without clamping and can be discarded
once the system has been installed.
The clamping rod will only operate smoothly if the
clamping plate has been properly adjusted. Only then
will the active leaf swing freely with the inactive leaf
closed.
Functional checks:
Open both door leaves and then hold the inactive leaf
in its open position.
The active leaf must then stay open at any angle.
Allow the inactive leaf to close.
The active leaf should close automatically once the
inactive leaf has reached its closed position.
9 Break out recesses for the 230 V power cable.
Lead all cables through and mount RMZ on base unit.
10 Terminal assignment
3 GND
Connection of external-
detectors with terminal
resistor
2) Total output
rating max. 9.8 W
12 + 24 V
14
1 +
24 V DC output to
hold-open device(s)
4 –
2
External manual release
PB with terminal resistor
10
7 NO
Floating change-over contact
(SELV)
24 V AC/DC, 1 A
8 NC
9 C
11 Floating terminal
16 Bus
E = Limit switch – this releases the inactive leaf when
the active leaf is pulled off/released from its hold-open
position.
Functions DIP switch
1 OFF = automatic reset
ON = manual reset
2
OFF = 1 radial operation (line)
ON = 2 radial operation (star)
3 OFF = without ceiling-mounted detector
ON = with ceiling-mounted detector
4
OFF = without manual push-button
ON = with manual push-button.
11
Lay the cable (shorten if necessary) for connecting the
hold-open device in the inactive leaf and connect to
terminals.
Ensure that the cable does not come into contact with
any moving parts and that it is not caught inside the
connecting rod.
12 Connect cable conductors to the active leave slide
channel terminals.
EMF inactive leaf
À
24 V DC from RMZ smoke detector
Á
.
Connect 24 V DC EMF power supply cable
Â
.
Connect any ceiling-mounted detectors and/or manual
pushbuttons – see connection diagrams.
Terminal resistors must be properly installed!
In order to comply with protection class II (total
insulation), the 230 V power lead should be installed
with double insulation up to the connection terminal.
Remove cable insulation at the end.
Connect 230 V power lead to terminals
Ã
.
Close the shock hazard protection cover and screw
down
Ä Å
.
13 Set the reset via the DIP switch
5.1 Automatic reset (delivery state)
The RMZ smoke detector automatically resets following
an alarm trip and as soon as there is no smoke or
test gas in the smoke chamber. Status display returns
to green.
5.2 Manual reset
A manual reset is mandatory in hold-open systems with
mit free-swing door closer.
Status display flashes green as soon as there is no
longer any smoke or test gas in the smoke chamber.
Reset is performed by pressing the reset pushbutton.
Status display lights green again.
If the manual reset mode has been implemented,
attach the enclosed RESET label.
14
Remove the red protective cap from the smoke detector
unit.
Switch on power supply – status display should show
green.
15 Setting the hold‑open point
GSR‑EMR 1
The hold-open point of the inactive leaf is adjustable
between approx. 80° and 130°. The active leaf is held
open by the door co-ordinator.
GSR‑EMR 1G
The hold-open point of the active leaf is adjustable
between approx. 80° and 130° (inactive leaf cannot be
held open).
GSR‑EMR 2
Both hold-open points can be adjusted independently
of one another between approx. 80° and 130°.
Open door leaves and engage hold-open
À
.
Loosen screws
Á
.
Open door to required hold-open angle and secure
Â
.
Re-tighten screws
Ã
.
The door cannot be opened beyond the hold‑open
point; fix a door stop at this position
Ä
.
2) See connection diagrams