DoorHan SHAFT-120 Скачать руководство пользователя страница 6

Страница: 6 / 12

OPERATOR SHAF T-120 INSTALLATION AND OPERATING MANUAL

7.2 Mounting via the chain operator

Additional accessories for installation can be purchased separately.

•

Mount the large sprocket on the gate shaft end.

•

Fix the bracket on the wall according to the length of the chain using dowels.

•

Secure the operator on the bracket using 4 bolts M10. Tension the chain, having adjusted the position of the operator.

•

8. Wiring

Very important: Always disconnect power before starting work with the control plate (connection, maintenance).

Connect the ground wire to the suitable terminal on the electric operator housing.

•

Always route the signal wires of control and safety devices separately from the supply cable 230V and power leads of

•

electric motors using separate flutes and tubes.

The cable wires must be protected from the contact with any rough and sharp parts.
In order to protect electric elements from moisture, tighten the waterproofing reducing coupling of the cable input by turning the plastic

nut.

1. Selection of supply voltage (terminal block X7)
To select voltage 220V, connect ‘CO’ and ‘400V’

2. Connection of supply voltage (terminal block X5)
Connect voltage 220V to terminals ‘L1’, ‘L3’.
Connect voltage 380V to terminals ‘L1’, ‘L2’, ‘L3’.

3. Motor (terminal block X4)
Connect motor to terminals ‘U’, ‘V’ and ‘W’.
380V motor: max. operating current < 9A, wattage

≤

4 kW

220V motor: max. operating current < 2.4A, wattage

≤

2.4 kW

4. End switches (terminal block X10)
Connect end switch wires ‘OP’ (opening switch), ‘CL’ (closing

switch) and ‘GND’ (common wire).

Mounting options

Torque (Nm)

Shaft speed (rpm)

Maximum amount of gate shaft

rotations

Direct transmission 1:1

120

Gear ratio 1:1,5

180

INSTALLATION

Voltage: 220V

Capacitor

Motor 220V

3�motor 380V

Voltage: 380V

Jumper

Open

Common

Voltage: 220V

Capacitor

Motor 220V

3�motor 380V

Voltage: 380V

Jumper

Open

Common

Voltage: 220V

Capacitor

Motor 220V

3�motor 380V

Voltage: 380V

Jumper

Open

Common

Voltage: 220V

Capacitor

Motor 220V

3�motor 380V

Voltage: 380V

Jumper

Open

Common

Shaft

Large gear wheel

Chain

Small gear wheel

The optional device is not included in the

standard package.

Содержание SHAFT-120













Результаты поиска

Содержание SHAFT-120

Отзывы:

Похожие инструкции для SHAFT-120

Бренды по названию

Популярные бренды

DoorHan SHAFT-120, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SHAFT-120

Отзывы:

Похожие инструкции для SHAFT-120

Бренды по названию

Популярные бренды