17
OPERATOR PROGRAMMING
Table 3.2. Advanced programming
Menu item
Function description
Default
0.1
Force at the 1st leaf: 1 – minimum force; 6 – maximum force
3
0.2
Force at the 2nd leaf: 1 – minimum force; 6 – maximum force
3
0.3
Maximum force at the initial moment: Y – function is on; n – function is off
n
0.4
Preliminary signal lamp switching on (5 sec.): 1 – 1 sec.; 2 – 2 sec.; 3 – 3 sec.; 4 – 4 sec.; 5 – 5 sec.
0
0.6
Photocell response for closing:
Y – door reverse movement after opening clearing; n – instant reverse
n
0.7
Automatic door closing after photocells response:
Y – function is on; n – function is off
n
0.8
Door opening/closing when buttons are pressed and hold (control commands from remote control are not executed):
Y – function is on; n – function is off
n
0.9
Prohibition on receiving control commands during door opening:
Y – function is on; n – function is off
n
1.0
Separate control logic:
START command – door opening and stop;
PEDESTRIAN command – door closing and stop;
Y – function is on; n – function is off
n
1.1
OUT1 universal output operation logic (see table 3.3)
2
1.2
Time of switching off of OUT1 output additional lighting after stop in: 0 – 0 sec.; 1 – 10 sec.; 2 – 20 sec.; 3 – 30 sec.;
4 – 60 sec.; 5 – 90 sec.; 6 – 120 sec.; 7 – 180 sec.; 8 – 360 sec.; 9 – 420 sec.
0
1.3
Remote recording of remote controls: Y – function is on; n – function is off
Y
1.4
Control command type of remote control button 1
0
1.5
Control command type of remote control button 2
0
1.6
Control command type of remote control button 3
0
1.7
Control command type of remote control button 4
0
1.8
Door quick movement function: Y – function is on; n – function is off
n
9.8
Parameters reset to factory settings
rE
9.9
Software version
Table 3.3. Operation logic of the universal output
Parameter
value
Operation mode
Open
Opening
Stopped
Closing
Closed
0
Accessories power supply
On
On
On
On
On
1
Indicator lamp for on mode
during opening
On
On
On
Flashing
Off
2
Additional lighting
On
(selected time*)
On
On
(selected time*
On
On
(selected time*
3
Traffic light mode
On
Off
Off
Off
Off
4
Switch on during opening
Off
On
Off
Off
Off
5
Switch on during closing
Off
Off
Off
On
Off
6
Output control by OUT(n)»
command
Switch on / switch off logic
7
Output impulse control by
OUT(n) command
1 second impulse
NOTE.
Before learning the door leaves are closing, when they reach the door stopper operator setting starts.
Start operator learning with the motor switched to M1 output to make one-leaf mode automatic.
*see p. 1.2, table 3.2
Содержание PCB-SW 24
