37
4) Motor conduction time for a drying cycle
1
You can select one of 1 hr/ 90 minutes/2 hours.
2
If a sports shoes course is selected and the time is selected, the motor conduction time is determined by a sports
shoes course.
3
Except for a sports shoes course, if the time is selected then the motor conduction time is determined by the
standard course.
5) Drying valve operation
1
20 seconds after drying starts, it continues until drying is completed) 10 sec on/ 10 sec off.
6) Cooling operation
1
Its purpose is to lower the temperature of the tank after drying is completed) The fan motor and the main motor
operate at the same time.
2
If the drum internal temperature is below 55 degrees, cooling is terminated.
3
The total duration of cooling is five minutes) If the internal temperature can’t be lowered, then the time is not
reduced anymore.
1) Steam water supply
1
In steam operation, the water is supplied twice for one minute each.
2
Constant temperature control is done until reaching the initial phase steam water supply point.
3
If the laundry is soaked in the water and the water level drops, then water is supplied again) To reduce the number
of water supplies, the water supply level is set to 10mm higher than the steam point (1.5 phase).
4
Depending on load sensing or the course setting value, the water supply level is chosen to be low or extra low.
5
If powder DET is injected, then the main washing valve is opened and closed five times.
6
If liquid DET is selected the liquid DET stirring motor operates for 30 sec for low levels and for 20 sec for extra
low levels) At this time, the main washing valve operates too.
7
When liquid DET is fully injected, then washing water supply including constant temperature control begins.
8
If powder DET is selected or liquid DET injection completion is memorized, then liquid DET injection process is
skipped.
9
If the water supply is completed, to clean the DET box, the main washing valve and the reserved washing valve
operate for 10 seconds.
2-6 Steam operation
Drying Option
Textile pulling
Cooling &
Wringkle free
Drying
Cycle time (min)
Heater ON/
OFF
Remarks
Cup-Borad
10/5
10/5
15/5
210
90/85
High Volt
Area
Very
10/5
10/5
15/5
260
90/85
Iron
10/5
10/5
15/5
60
90/85
Low
10/5
10/5
15/5
110
70/60
Time
10/5
10/5
15/5
30/60/90/120/150
/180/210/240/270
90/85
Air Refresh
10/5
10/5
15/5
35
80/70
Tub Clean
10/5
10/5
15/5
30
70/60
Wash & Dry
10/5
10/5
15/5
40
90/85
Cup-Borad
10/5
10/5
15/5
210
90/85
Low Volt
Area
Very
10/5
10/5
15/5
260
90/85
Iron
10/5
10/5
15/5
60
90/85
Low
10/5
10/5
15/5
110
70/60
Time
10/5
10/5
15/5
30/60/90/120/150
/180/210/240/270
90/85
Air Refresh
10/5
10/5
15/5
35
80/70
Tub Clean
10/5
10/5
15/5
30
70/60
Wash & Dry
10/5
10/5
15/5
40
90/85
WFC3V11ZDNH01D2GW(DWC-PS1512X)_칠레향(SM).indd 37
2017-10-26 오후 4:17:40
Содержание DWC-PS1512X
Страница 10: ...8 2 INLET BOX AS WFC3V11ZDNH01D2GW DWC PS1512X _칠레향 SM indd 8 2017 10 26 오후 4 17 31 ...
Страница 12: ...10 3 CABINET F ASSY WFC3V11ZDNH01D2GW DWC PS1512X _칠레향 SM indd 10 2017 10 26 오후 4 17 32 ...
Страница 15: ...13 5 BASE U AS 1 2 3 5 4 WFC3V11ZDNH01D2GW DWC PS1512X _칠레향 SM indd 13 2017 10 26 오후 4 17 34 ...
Страница 69: ...67 6 WIRING DIAGRAM WFC3V11ZDNH01D2GW DWC PS1512X _칠레향 SM indd 67 2017 10 26 오후 4 17 43 ...
