Donaldson Torit DB-800 Скачать руководство пользователя страница 2

Donaldson Company, Inc.

i

  The Safety Alert Symbol indicates a hazardous situation which, if not avoided could 

result in death or serious injury. Obey all safety messages following this symbol to 

avoid possible injury or death. The possible hazards are explained in the associated 

text messages.

CAUTION, used with the safety alert symbol, indicates a hazardous situation 

which, if not avoided, could result in minor or moderate injury.
NOTICE indicates a potential situation or practice which is not expected to result 

in personal injury, but which if not avoided, may result in damage to equipment.

This manual has been supplied to assist with the installation, operation and maintenance for the collector purchased. 

Please read the manual before installing, operating, or performing maintenance on the collector as it contains 

specific precautions for worker safety. It is the owner’s responsibility to ensure that this manual is available for use by 

installers, operators and maintenance personnel that will be working with this collector. This manual is the property of 

the owner and should be left with the collector when installation has been completed. DO NOT operate this collector 

until you have read and understood the instructions and warnings located in the installation and operation manual.

For additional copies of this manual, contact Donaldson Torit

IMPORTANT NOTES

Содержание Torit DB-800





















Отзывы: