Donaldson Torit UMA 100H Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 57

Donaldson Torit UMA 100H Скачать руководство пользователя страница 33

Installation, Operation and Maintenance Manual

Unimaster Dust Collectors – Series UMA 40-750

33

MAINTENANCE

Renewal of fan bearings (fig. 13)

  1  Isolate electrical supply and remove fan chamber lid.
  2  Disconnect electrical wiring to terminal box.
  3  Remove the four bolts securing the motor drive bed-plate and withdraw the

complete assembly from the unit case.

4 Loosen, but do not remove, the four socket screws in the base flange and

withdraw drive cover.

5 Remove drive belt.
6 Remove the six nuts securing flange of bearing housing to the bed-plate and

withdraw the housing.

  7  Remove fan pulley and the six bolts securing the fan case.
  8  Remove fan impeller and fan case.
  9  Remove end caps and spacers from fan bearing housing.
10  Remove fan bearings.
11  Fit new bearings, ensuring that the fan end bearing is flush with bearing

housing.

12 Flush out bearings with a degreasing solvent (a special high temperature

grease is required as step '14').

13 When inside of bearings is dry, apply a small amount of light oil to the bearings

and spin the shaft round.

14 Repack with Shell Alvania ET3 grease (or equivalent) as shown in figure

13.

15 Secure bearing end caps and reassemble all other items to shaft, tightening

up securely.

16  Refit fan unit to bed-plate. (Air discharge towards motor).
17  Tension drive belt as shown in figure 14.
18  Replace drive cover and tighten four socket screws.
19  Reconnect electrical wiring to terminal box.
20  Recheck fan rotation (see fig. 14).

Figure 14 V-belt tensioning (UMA 40MM)

2 kg force should give
6 mm deflection

«
...
31
32
33
34
35
...
»

Содержание UMA 100H


























































Отзывы:

Нет отзывов