manualshive.com logo in svg

Donaldson Torit UMA 100H, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Donaldson Torit UMA 100H Скачать руководство пользователя страница 16

Installation, Operation and Maintenance Manual

Unimaster Dust Collectors – Series UMA 40-750

16

  3  Using the sealant supplied in the fixing pack, seal all around the underside 

of the seating flange (see fig. 9).

  4  Lay the acoustic diffuser down so that the lifting brackets are uppermost.
  5  Using the four-point lifting method, lift the acoustic diffuser into position on 

top of the fan section, so that the diffuser outlet is at the front, right-hand 
corner of the top plate (see fig. 10).

  6  The  acoustic  diffuser  can  now  be  fixed  in  position  using  M10  bolts  and 

washers at the sides, and self-tapping screws at the front and rear.

INSTALLATION

SECTION A 

−

 A

(Refer to figure 10)

Acoustic diffuser 
side plate

Fan section 
top plate

Apply sealant 
to this face

Figure 9  Applying sealant to the UMA 750 acoustic diffuser

Figure 8  Earthing connection

Earthing strap

Upper section 
side panel

Bottom assembly

Figure 10  Fitting the UMA 750 acoustic diffuser

Outlet at front 
right-hand corner

M10 bolts and washers

Acoustic diffuser

Self-tapping screws, 
front and rear

Fan chamber 
access door

A

A

Содержание UMA 100H


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды