manualshive.com logo in svg

Donaldson Torit UMA 100H, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Donaldson Torit UMA 100H Скачать руководство пользователя страница 11

Installation, Operation and Maintenance Manual

Unimaster Dust Collectors – Series UMA 40-750

11

INSTALLATION

All collectors are delivered to site either upright or laid on their side, in one piece 
or in a number of pieces depending on their configuration.
Lifting brackets are provided on all collectors except the UMA 40 and 40MM.  
They are also fitted to the UMA 100 to 750 bottom assemblies when supplied 
separate to the main filter case.  Where headroom is restricted, a fork lifting option 
is available on all collectors except for the UMA 750V.  The UMA 750 fan type 
collectors have a lifting beam within the fan chamber, while the smaller collectors 
are lifted from underneath the seal frame after filter assembly removal.

General guidance to lifting

  During all lifting operations a crane or fork lift with an adequate SWL (safe 

working load) must be used.  (Refer to lifting labels located adjacent to 
lifting fixture for weight of equipment supplied by Donaldson).

  It  may  be  necessary  to  guide  the  collector  during  lifting  to  prevent 

excessive swing.

  If a fork lift is used to lift the collector using the lifting brackets, a suitable 

lifting attachment must be used to prevent the chains slipping off the 
forks (see fig. 2).

  If  chains  or  slings  are  used  they  must  have  an  adequate  SWL  (safe 

working load).  (Refer to lifting labels located adjacent to lifting brackets 
for weight of equipment supplied by Donaldson).

Figure 4  Lifting collector to vertical position

≤

 

90

°

≤

 

90

°

OR

PREFERRED 

LIFTING METHOD

Содержание UMA 100H


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды