DOMUSA TEKNIK Fusion Hybrid Oil Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 52

DOMUSA TEKNIK Fusion Hybrid Oil Скачать руководство пользователя страница 6

Fusion Hybrid Oil

4

1.4

General installation guidelines

DOMUSA TENIK

ensures that this product contains no harmful substances and that no harmful

materials have been used in its manufacture.
Please carefully read this instruction manual and keep it in a safe, easily accessible place.

DOMUSA

TEKNIK

shall not be held liable for any damage that may occur due to failure to follow these

instructions.
The

Fusion Hybrid Oil

module can only be installed in combination with a heat pump from the

DUAL CLIMA

line from

DOMUSA TEKNIK

. The

FUSION

module, in combination with a

DUAL CLIMA

heat pump, is suitable for use in both heating and cooling installations, and can be combined with
fan coils, underfloor heating/cooling and low-temperature radiators. It should be connected to a

heating/cooling system and to a hot water distribution network that is compatible with its

performance and power.
This appliance should only be used for the purpose for which it has been expressly designed. Any

other use is considered unsuitable and therefore hazardous. The manufacturer shall not be
considered liable under any circumstances for damage caused by unsuitable, erroneous or

improper use.
Improper installation or placement of equipment or accessories may cause electrocution, short

circuit, leakage, fire, or other damage to the equipment. Use only accessories or optional
equipment manufactured by

DOMUSA TEKNIK

and specifically designed to work with the products

presented in this manual. Do not modify, replace or disconnect any safety or control device without
first consulting the manufacturer or the Official Technical Assistance Service of

DOMUSA TEKNIK

.

Current legislation must be taken into account on installing this appliance, and it must be installed

in a place with suitable ventilation.
The module must be installed by an installer authorized by the Ministry of Industry and it must be
started up by an Official Technical Assistance Service authorized by

DOMUSA TEKNIK

..

The module must be installed considering the requirements demanded at each installation site:



The Technical Building Code.



The Regulation for Heating Installations in Buildings.



The Low Voltage Regulation.



The Codes of good practice and regulations refer to the latest versions of the same.

«
...
4
5
6
7
8
...
»

Содержание Fusion Hybrid Oil





















































Отзывы:

Нет отзывов