DOMUSA TEKNIK Evolution Solar 30 HDX Скачать руководство пользователя страница 27

Страница: 27 / 60

8.4

Heating circuit 2 functioning (Optional)

All the models in the

Evolution Solar HDX

range of boilers have the option of controlling a second

heating circuit. This requires the installation of a second circulation pump on the boiler. To correctly

install this pump, carefully follow the instructions given in the “Installing heating circuit 2” section

of this manual.

Heating circuit 2 will work with the selected boiler setpoint temperature (see “

Selecting the boiler

setpoint temperature

” ) and the temperature of room thermostat 2 (

TA2

) (if the boiler has one). The

burner and the heating pump of circuit 2 (

) will begin to function until the installation reaches

the selected boiler setpoint temperature (or the temperature on room thermostat 2 (if the unit has

one). When the temperature of the installation drops below the selected boiler temperature, the

burner will start up again, running the heating cycle.

NOTE: When the heating function is disabled, if OFF is selected circuit 2 will also be disabled.

8.5

Functioning with an SRX2/EV Underfloor Heating Kit (Optional)

The

Evolution Solar HDX

boiler may optionally be supplied fitted with an SRX2/EV underfloor

heating kit (fitted to heating circuit 1). This kit basically consists of a motorised 3-way mixing valve

and an underfloor heating installation flow temperature sensor.

The underfloor heating installation is worked by the electronic boiler control. The installation flow

sensor is used to adjust the temperature, selecting the installation flow setpoint temperature using

the boiler setpoint adjustment touch button on the control panel, between OFF, 0 and 45 ºC (see

“

Selecting the Underfloor Heating flow setpoint temperature

”). In this operating mode, the

electronic control sets the boiler setpoint temperature to 75ºC by default, and the installation flow

temperature can be adjusted to the selected setpoint temperature using the mixing valve.
The boiler setpoint temperature can be changed using the MODE touch button to browse to the

“

boiler setpoint temperature

" display option. When the display shows this option, touch the "+ /-"

symbols to select the desired temperature.

If you wish, the SRX2/EV Underfloor Heating circuit function can be totally disabled, by selecting
"

OFF

" as the installation flow setpoint temperature.

NOTE: When the Underfloor Heating circuit function is disabled by selecting OFF as the

setpoint temperature, only circuit 1 will be disabled. Circuit 2 will continue to function.

Содержание Evolution Solar 30 HDX





























































Результаты поиска

Содержание Evolution Solar 30 HDX

Отзывы:

Похожие инструкции для Evolution Solar 30 HDX

Бренды по названию

Популярные бренды

DOMUSA TEKNIK Evolution Solar 30 HDX, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Evolution Solar 30 HDX

Отзывы:

Похожие инструкции для Evolution Solar 30 HDX

Бренды по названию

Популярные бренды