Dometic RM7030 Скачать руководство пользователя страница 31

Страница: 31 / 38

DOMETIC® RM7030/RM7732

Refrigerators

DIAGNOSTIC SERVICE MANUAL

9.9

INTERIOR LINER SEAL TO FRAME

There is a seal that is applied to the liner in the area

where the metal frame makes contact with the interior

liner. If this seal is incomplete, cold air can migrate out

to the metal frame. If this happens, condensation could

form on the frame and could promote rapid formation of

frost. If you suspect an improper seal, apply a small

bead of silicone all the way around the perimeter where

the frame meets the interior liner.
Remove all screws securing the refrigerator into the

cabinet and slide the refrigerator out approximately 24

inches. Clean the metal frame and foil-backed insulation

around the refrigerator. Apply a foil-backed adhesive

tape to the joint between outer frame and foil-backed

refrigerator insulation. Refer to illustration top of page

22.

Make sure the refrigerator is dry and that the surface

temperatures are above 50°F. Use a clear silicon

caulking compound and seal the seam between the

refrigerator's plastic liner and the metal frame. Apply the

silicon in a continuous bead around both the refrigerator

freezer and food compartments.

NOTE: TO FORM A PROPER SEAL, IT IS IMPOR-

TANT NOT TO LEAVE ANY GAPS.

(Section 10. Icemaker Operation, continue to Page 29)

All manuals and user guides at all-guides.com

all-guides.com

Содержание RM7030







































Результаты поиска

Содержание RM7030

Отзывы:

Похожие инструкции для RM7030

Бренды по названию

Популярные бренды

Dometic RM7030, Руководство по обслуживанию

Результаты поиска

Содержание RM7030

Отзывы:

Похожие инструкции для RM7030

Бренды по названию

Популярные бренды