Dometic RM7030 Скачать руководство пользователя страница 15

Страница: 15 / 38

DOMETIC® RM7030/RM7732

Refrigerators

DIAGNOSTIC SERVICE MANUAL

5.7

FUSES

A. RM7030 (Product No. 921890201 & 921890301)

The fuse is to protect the circuit board. To check the

fuse, remove it from the holder and do a continuity

check. If no continuity, replace it with a proper 3-amp

time delay fuse.

B. RM7030 (Product No. 921890401) and RM7732

The fuses are to protect the circuit board and the

integrity of the heater circuit(s) against shorts.
The 3-amp DC fuse is designed to protect the circuit

board from internal shorts. The 5-amp AC fuse is

designed to protect the integrity of the AC heater circuit

from shorts.
To check the fuses, remove from the holder and do a

continuity check. If no continuity, replace with a proper

amperage fuse.

NOTE: Determine the cause of the fuse failure and

correct before replacing fuse.

7-PIN

CONNECTOR

6-PIN

CONNECTOR

10-PIN

CONNECTOR

5.8

UPPER CIRCUIT BOARD

RM7030 (Product No. 921890201 & 921890301)

A. ON-OFF SWITCH

NOTE:

The following checks should be made on the

upper circuit board and harness assembly

BEFORE

replacing the upper circuit board or wiring

harness. The checks are to be done with the

wiring harness

REMOVED

from the lower

circuit board.

With the switch in the "ON" position:

CONTINUITY should be indicated be-

tween the orange terminal to the yellow

terminal on the 10-pin connector.

ORANGE

YELLOW

10 PIN

CONTINUITY should be indicated between

the brown terminal to the red terminal on the

10-pin connector.

BROWN

RED

10 PIN

YELLOW

GREEN

10 PIN

RED

BLUE

10 Pin

7 Pin

NO continuity should be indicated between

the yellow terminal to the green terminal

on the 10-pin connector.

NO continuity should be indicated

between the red terminal on the 10-

pin connector to the blue terminal

on the 7-pin connector.

With the switch in the "OFF"

position:

CONTINUITY should be indicated

between the yellow terminal to the green

terminal on the 10-pin connector.

YELLOW

GREEN

10 PIN

RED

BLUE

10 Pin

7 Pin

CONTINUITY should be indicated

between the red terminal on the 10-

pin connector to the blue terminal on

the 7-pin connector.

NO continuity should be indicated

between the orange terminal to the

yellow terminal on the 10-pin connector.

NO continuity should be indicated between the

brown terminal to the red terminal on the 10-

pin connector.

NOTE: If any of these checks on the ONOFF

switch are not correct, verify the wire harness

has continuity. If the wire harness is good,

replace the upper circuit board.

BROWN

RED

10 PIN

ORANGE

YELLOW

10 PIN

All manuals and user guides at all-guides.com

Содержание RM7030







































Результаты поиска

Содержание RM7030

Отзывы:

Похожие инструкции для RM7030

Бренды по названию

Популярные бренды

Dometic RM7030, Руководство по обслуживанию

Результаты поиска

Содержание RM7030

Отзывы:

Похожие инструкции для RM7030

Бренды по названию

Популярные бренды